Kenmore Elite 79095073310 electric range Parts

To reset the oven controls on your Kenmore Elite 79095073310 electric range back to factory defaults, press and hold 7 on the numeric keypad for about 6 seconds until the acceptance tone sounds, then press START. This restores the original control settings.

This procedure resets the electronic oven control settings, not the house breaker.

• Resets 12/24-hour clock display preference
• Resets silent or audible keypad tones
• Resets Fahrenheit/Celsius display preference
• Clears any saved recipes (if your model supports them)
• Resets any oven temperature offset back to 0

For the exact button locations and menu behavior on model 79095073310, use the 79095073310 owner's manual.

1. Make sure the control panel is responsive (display on).
2. Press and hold 7 on the numeric keypad.
3. Keep holding until you hear a tone (about 6 seconds).
4. Press START once.

After power is restored, we recommend you:

• Turn the range off if it was left on
• Reset the clock
• Re-select your desired oven function (Bake, Broil, Convection)

Details for post-outage behavior are also covered in the 79095073310 owner's manual.

A factory reset is the fastest way to clear confusing control behavior after setting changes, and it also eliminates an incorrect temperature offset that can cause baking results to run hot or cold.

Last updated: February 2026

On Kenmore Elite electric range model 79095073310, the model and serial number are printed on the identification plate attached to the lower right oven frame. You can access it by opening the storage drawer or warming drawer (depending on your range configuration); see the 79095073310 owner's manual for the exact location diagram.

• Pull out and open the storage drawer (some models) and look at the lower right oven frame.
• If your range has a warming drawer, open it and check the lower right oven frame.
• Use a flashlight and look for a label that lists Model No. and Serial No.
• Write the numbers down exactly as shown; this helps match the correct Kenmore parts and diagrams.

We use the model number to match the correct replacement parts for your range, such as an oven temperature sensor, bake element, or control board. Even small model-number differences can change which parts fit.

Last updated: February 2026

Kenmore model numbers are read in sections: the first 3 digits identify who built the appliance, and the remaining digits identify the specific design and feature set. For Kenmore Elite electric range model 79095073310, the 790 prefix points to a Frigidaire-built range; use the full model number when matching parts and manuals.

Most Kenmore model numbers follow this pattern:

• Prefix (first 3 digits): manufacturer code (who actually made it)
• Core digits: the base platform or series
• Trailing digits: feature, color, or revision differences that affect part fit
• Full model number: the only safe way to ensure correct parts compatibility

For this range, the Use and Care Guide shows the family format as 790.9507*, which matches your model series. Check the 79095073310 owner's manual for the exact labeling and any series notes.

On Kenmore Elite 79095073310 ranges, the identification plate is typically located here:

• Open the storage drawer (some models), or
• Open the warmer drawer (some models)
• Look on the lower right oven frame for the model and serial plate

This location matters because the model number on the frame is the one we use to match parts like the oven sensor, control board, or door lock.

Kenmore is a brand label; different manufacturers built different Kenmore appliances. The prefix helps narrow down the correct parts system and design.

When you shop or troubleshoot, match parts to the full model number. For example, if you are diagnosing baking temperature issues, the frigidaire range oven temperature sensor 316490000 is a common part used to help the control regulate oven temperature.

A single digit difference in a Kenmore model number can change the oven control board, wiring harness, door lock style, or induction component set. Using 79095073310 avoids returns and speeds up repair.

Last updated: February 2026

Yes. Kenmore Elite is Kenmore’s higher-end line, and your Kenmore Elite electric range model 79095073310 is built to deliver more premium cooking features and performance than standard Kenmore models (for example, induction cooking and advanced oven functions described in the owner's manual).

Kenmore Elite typically sits in the upper-mid to high-end tier for mainstream appliances. In practical terms, that usually means:

• More cooking features (such as induction cooking zones on many Elite models)
• More precise temperature management and cooking modes
• Higher-end styling and control layouts
• More complex electronics (control boards, sensors, and safety switches)

Use this quick comparison to set expectations when shopping parts or troubleshooting.

A “higher-end” range often uses more sensors and control components to manage performance. When symptoms show up (temperature issues, error codes, fan problems), diagnosis usually focuses on a few common components:

• Oven temperature sensing (example: frigidaire range oven temperature sensor 316490000)
• Electronic control issues (example: range oven control board 316650011)
• Convection airflow problems (example: range convection fan motor 316256100)

These checks help you decide if a repair is straightforward or likely to involve higher-cost electronics:

• Confirm whether the issue is oven-related, cooktop-related, or both
• Look for consistent symptoms (always too hot, always too cool, intermittent shutdown)
• Check for visible wiring damage or loose connections (power off first)
• Use the troubleshooting section in the owner's manual to match symptoms to likely causes

Knowing Kenmore Elite is a higher-end line helps set expectations: you often get better performance and features, but repairs can involve more electronic parts and more precise troubleshooting.

Last updated: February 2026

If your Kenmore Elite 79095073310 electric range is not working, the most common causes are a tripped double breaker, a loose/burned power connection at the terminal block, or the control needing a reset after a power interruption. Start with power checks, then isolate whether the cooktop or oven is affected.

• Reset the double 240V breaker fully OFF, then ON.
• If power just returned, turn all controls OFF; then reset the clock and oven function as shown in the 79095073310 owner's manual.
• Check for a control lock or cooktop lockout mode (if enabled).
• If the range was in a cold space, keep it above 32°F for 3 hours before powering on.
• Look for a burned smell, melted wire insulation, or a loose cord where it connects.

• If you find heat damage or loose/burned terminals where the cord attaches, replace the universal/multiflex (frigidaire) range terminal block 5303935271.
• If the oven heats inconsistently or runs hot/cold, the frigidaire range oven temperature sensor 316490000 is a common fix.
• If the display is erratic or the oven won’t respond to commands, the range oven control board 316650011 is a likely suspect.

Electric ranges often fail due to power delivery problems or a control reset issue, not a major oven component. Confirming stable 240V power and solid terminal connections prevents unnecessary part replacement.

Last updated: February 2026