Kenmore 11060172002 commercial dryer Parts

For Kenmore commercial dryer model 11060172002, the correct drum belt is the Dryer drum belt 341241. Belt “size” is best matched by model number because length and rib profile vary across Kenmore (Whirlpool-made) dryers, even when they look similar.

How to confirm you have the right belt

We recommend matching by model number and belt style (ribbed vs. flat) before ordering.

• Confirm the model tag reads 11060172002
• Compare the old belt’s width and rib pattern to the replacement
• Check for belt glazing, cracks, or missing ribs (signs it slipped)
• Inspect the idler pulley and drum rollers while the belt is off
• Use the belt routing diagram in the 11060172002 owner's manual

Common belt-related symptoms (and what they usually mean)

Symptom	Most common cause	What to check next
Drum will not turn, motor runs	Broken or slipped belt	Belt condition and routing
Squealing or chirping	Worn idler pulley or rollers	Idler pulley, roller shafts
Thumping	Flat-spotted rollers	Roller wear and shafts
Burning rubber smell	Belt slipping	Drum drag, idler tension

If you’re already opening the cabinet, many techs replace wear items together using a kit to prevent repeat breakdowns.

• Dryer drum belt 341241
• Dryer repair kit 4392065
• Dryer idler pulley WP691366

Why it matters

A belt that is the wrong length or profile can slip, overheat, or fail early. On a commercial dryer like Kenmore 11060172002, correct belt fit also helps maintain proper drum speed and drying performance.

Last updated: January 2026

To hard reset a Kenmore dryer like model 11060172002, we disconnect power long enough to clear the control and then restore power for a fresh start. If the dryer still will not run or heat after the reset, we troubleshoot power, door closure, and overheating protection next using the 11060172002 owner’s manual.

Hard reset steps (safe, quick)

• Turn the dryer OFF.
• Unplug the power cord (or switch the breaker OFF).
• Wait 1 to 5 minutes.
• Restore power.
• Close the door fully, then press and hold PUSH BUTTON TO START for 2 to 5 seconds.

If the reset does not fix it

A reset clears a temporary control issue, but it will not fix a failed safety device or a power problem.

• Confirm the door is fully closed.
• Check the home’s two fuses or two breakers (many electric dryers use two).
• Verify the dryer has a proper 240-volt supply (electric models).
• If the drum turns but there is no heat, check for a tripped breaker or blown fuse first.
• If the dryer stopped after overheating, inspect and clean the venting and lint path.

Common “won’t start” causes and what to check

Symptom	Most likely check	What we do next
No response at all	Power supply	Check both breakers/fuses, then retry Start hold
Runs only with door held	Door switch/door alignment	Inspect latch alignment and switch operation
Stops mid-cycle, then won’t restart	Overheat protection/airflow	Clean venting, then test thermal safety parts

Parts that often relate to no-start or overheat symptoms

If airflow is restricted, safety devices can open to protect the dryer. For this model, common service parts include the dryer thermal cut-off fuse kit 279816 and temperature controls like the dryer high-limit thermostat WP3977767.

Why it matters

A hard reset is a good first step, but repeated shutdowns usually point to power delivery or restricted airflow. Fixing the root cause helps prevent repeat failures and reduces drying time.

Last updated: January 2026

For Kenmore model 11060172002, replacing the heating element typically costs $150 to $350 total with professional service (part plus labor). If you do it yourself, you usually pay $40 to $150 for the heater and any small wiring parts.

Typical cost breakdown (DIY vs. pro)

• Heating element (part only): commonly $40 to $150
• Labor/service call: commonly $100 to $250
• Extra parts sometimes needed: terminals or a wire kit if connections are heat-damaged
• Total installed: typically $150 to $350

Scenario	What you pay for	Typical total
DIY replacement	Part (and possibly a wire kit)	$40 to $150
Pro replacement	Part + labor/service call	$150 to $350

What changes the price on model 11060172002

• Access time: commercial cabinets and panels can take longer to open and reassemble
• Overheating damage: a restricted vent can overheat the heater housing and damage wiring
• Multiple failed heat parts: a blown thermal cut-off or failed thermostat can be found during diagnosis
• Downtime urgency: after-hours or rush service increases labor cost

Before you buy a heating element (quick, accurate checks)

Because 11060172002 uses an electric heating circuit, confirm the no-heat problem is not caused by power or safety devices.

• Verify the dryer is getting 240 volts (a tripped breaker can leave the drum running but no heat)
• Check for a blown thermal cut-off such as dryer thermal cut-off fuse kit 279816
• Inspect heater wiring; if terminals are burnt, consider dryer heating element wire kit 279457
• Use the wiring diagram and access steps in the 11060172002 owner's manual

Why it matters

A no-heat complaint is often caused by power supply issues, airflow restriction, or a blown thermal cut-off, not only the heater. Diagnosing first prevents repeat failures and avoids paying twice for parts and labor.

Last updated: January 2026