Owner’s manual
Error Codes
What size belt do I need for a Kenmore dryer?
For Kenmore commercial dryer model 11060172002, the correct drum belt is the Dryer drum belt 341241. Belt “size” is best matched by model number because length and rib profile vary across Kenmore (Whirlpool-made) dryers, even when they look similar.
We recommend matching by model number and belt style (ribbed vs. flat) before ordering.
- Confirm the model tag reads 11060172002
- Compare the old belt’s width and rib pattern to the replacement
- Check for belt glazing, cracks, or missing ribs (signs it slipped)
- Inspect the idler pulley and drum rollers while the belt is off
- Use the belt routing diagram in the 11060172002 owner's manual
| Symptom | Most common cause | What to check next |
|---|---|---|
| Drum will not turn, motor runs | Broken or slipped belt | Belt condition and routing |
| Squealing or chirping | Worn idler pulley or rollers | Idler pulley, roller shafts |
| Thumping | Flat-spotted rollers | Roller wear and shafts |
| Burning rubber smell | Belt slipping | Drum drag, idler tension |
If you’re already opening the cabinet, many techs replace wear items together using a kit to prevent repeat breakdowns.
A belt that is the wrong length or profile can slip, overheat, or fail early. On a commercial dryer like Kenmore 11060172002, correct belt fit also helps maintain proper drum speed and drying performance.
Last updated: January 2026
How to hard reset a Kenmore dryer?
To hard reset a Kenmore dryer like model 11060172002, we disconnect power long enough to clear the control and then restore power for a fresh start. If the dryer still will not run or heat after the reset, we troubleshoot power, door closure, and overheating protection next using the 11060172002 owner’s manual.
- Turn the dryer OFF.
- Unplug the power cord (or switch the breaker OFF).
- Wait 1 to 5 minutes.
- Restore power.
- Close the door fully, then press and hold PUSH BUTTON TO START for 2 to 5 seconds.
A reset clears a temporary control issue, but it will not fix a failed safety device or a power problem.
- Confirm the door is fully closed.
- Check the home’s two fuses or two breakers (many electric dryers use two).
- Verify the dryer has a proper 240-volt supply (electric models).
- If the drum turns but there is no heat, check for a tripped breaker or blown fuse first.
- If the dryer stopped after overheating, inspect and clean the venting and lint path.
| Symptom | Most likely check | What we do next |
|---|---|---|
| No response at all | Power supply | Check both breakers/fuses, then retry Start hold |
| Runs only with door held | Door switch/door alignment | Inspect latch alignment and switch operation |
| Stops mid-cycle, then won’t restart | Overheat protection/airflow | Clean venting, then test thermal safety parts |
If airflow is restricted, safety devices can open to protect the dryer. For this model, common service parts include the dryer thermal cut-off fuse kit 279816 and temperature controls like the dryer high-limit thermostat WP3977767.
A hard reset is a good first step, but repeated shutdowns usually point to power delivery or restricted airflow. Fixing the root cause helps prevent repeat failures and reduces drying time.
Last updated: January 2026
How much does it cost to replace a heating element in a Kenmore dryer?
For Kenmore model 11060172002, replacing the heating element typically costs $150 to $350 total with professional service (part plus labor). If you do it yourself, you usually pay $40 to $150 for the heater and any small wiring parts.
- Heating element (part only): commonly $40 to $150
- Labor/service call: commonly $100 to $250
- Extra parts sometimes needed: terminals or a wire kit if connections are heat-damaged
- Total installed: typically $150 to $350
| Scenario | What you pay for | Typical total |
|---|---|---|
| DIY replacement | Part (and possibly a wire kit) | $40 to $150 |
| Pro replacement | Part + labor/service call | $150 to $350 |
- Access time: commercial cabinets and panels can take longer to open and reassemble
- Overheating damage: a restricted vent can overheat the heater housing and damage wiring
- Multiple failed heat parts: a blown thermal cut-off or failed thermostat can be found during diagnosis
- Downtime urgency: after-hours or rush service increases labor cost
Because 11060172002 uses an electric heating circuit, confirm the no-heat problem is not caused by power or safety devices.
- Verify the dryer is getting 240 volts (a tripped breaker can leave the drum running but no heat)
- Check for a blown thermal cut-off such as dryer thermal cut-off fuse kit 279816
- Inspect heater wiring; if terminals are burnt, consider dryer heating element wire kit 279457
- Use the wiring diagram and access steps in the 11060172002 owner's manual
A no-heat complaint is often caused by power supply issues, airflow restriction, or a blown thermal cut-off, not only the heater. Diagnosing first prevents repeat failures and avoids paying twice for parts and labor.
Last updated: January 2026
