Kenmore 11062612101 electric dryer Parts

Your Kenmore dryer’s model is printed on the model and serial number plate; for this parts page, the model is 11062612101. Use that exact model number when ordering parts or checking specifications in the 11062612101 owner's manual.

On Kenmore electric dryers like model 11062612101, the model and serial number plate is typically located where it’s easy to reference during service.

• Inside the dryer door opening on the cabinet frame
• On the back panel of the dryer cabinet
• Near the lint screen housing area (depending on the exact console and cabinet style)
• On a metal plate or durable label (not a paper sticker)

Kenmore model numbers are the key to getting the right replacement parts (belt, heating element, thermostat, timer) and the correct wiring and installation requirements.

Even small model-number differences can change the correct drum belt length, heating circuit parts, or door switch style. Using 11062612101 helps ensure parts like the dryer drum belt 341241 match your dryer correctly.

• Copy the model number exactly as printed (all digits)
• Record the serial number too (helpful for service)
• Confirm your dryer type: Kenmore electric dryer
• Use the manual for operating and installation details: 11062612101 owner's manual

Last updated: February 2026

The Kenmore electric dryer model 11062612101 is a 29-inch wide dryer. For planning space, most installations also need at least 5 1/2 inches of clearance behind the dryer for the exhaust vent and elbow; confirm your exact layout in the 11062612101 owner's manual.

Here are the model-specific sizing details we use most often for fit and installation:

• Width: 29 inches (cabinet width)
• Behind-dryer clearance: minimum 5 1/2 inches for the vent and elbow (typical setup)
• Door clearance: allow enough room for the door to open fully
• Side clearance: 1 inch on all sides is recommended to reduce noise transfer
• Closet installs: a door requires top and bottom ventilation openings

Dryer “size” is not just the cabinet width. Venting clearance and door swing space directly affect drying performance, safety, and whether the dryer can be serviced without pulling it out.

• Verify the outlet location is within about 2 ft of either side of the dryer.
• Make sure the floor is level (a slope over 1 in. can affect tumbling and sensor cycles).
• Keep the dryer in a location above 45°F for normal automatic-cycle shutoff.

Last updated: February 2026

The average lifespan of the Kenmore 11062612101 electric dryer is 13 years. Regular lint cleaning, correct venting, and replacing wear parts (belt, rollers, thermostats) on time are what most often determine whether it reaches that full service life.

• Venting and airflow: Long or restricted vent runs raise heat and strain components.
• Lint control: Clean the lint screen every load; keep the exhaust path clear.
• Heat management: Overheating shortens the life of the heating circuit and safety fuses.
• Wear parts: Drum support parts and the belt wear gradually and can be renewed.
• Electrical supply: A stable 240V supply and tight connections reduce nuisance failures.

Proper vent length is a major life extender because it keeps temperatures and dry times in a normal range. Use the vent length chart in the installation guide when planning your run.

If the dryer still heats but is noisy, slow to dry, or stops mid-cycle, these are common maintenance replacements for this model:

• Dryer drum belt 341241 (belt wear, slipping, drum not turning)
• Dryer repair kit 4392065 (typical drum support wear items)
• Dryer thermal cut-off fuse kit 279816 (overheat protection that can open if airflow is poor)
• Dryer operating thermostat WP3387134 (temperature regulation)

A dryer that is properly vented and maintained dries faster, runs cooler, and cycles normally; that reduces stress on the heating element, thermostats, motor, and wiring, which is what helps the 11062612101 reach its expected 13-year lifespan.

Last updated: March 2026