Kenmore 66513049K116 dishwasher Parts

To identify your Kenmore dishwasher model, we check the rating label on the dishwasher itself. On Kenmore model 66513049K116, the label is typically found just inside the door area and lists both the model number and serial number.

Where to find the model number label

Look in these common spots (in order):

• Along the inside edge of the door (top or side)
• On the left-hand side of the door opening (common on many Kenmore units)
• On the frame around the tub opening (near the latch area)
• On the side of the tub visible when the door is open

If the label is worn or hard to read, use a flashlight and wipe the area with a damp cloth to remove detergent film.

What to write down (and why)

Record these items exactly as shown:

• Model number (example format: 665.1304*)
• Serial number (used to identify production run and date code)
• Type/series info (sometimes listed near the model)
• Any suffix letters/numbers (they matter for part compatibility)

Quick reference table

Label item	What it’s used for	Example you might see
Model number	Matching parts and diagrams	665.1304* / 66513049K116
Serial number	Verifying production details	A long letter-number code

Why it matters

Kenmore dishwashers often share similar looks across multiple 665-series models, but parts like the control, racks, and pumps can vary by revision. Using the exact model number from the rating label helps us match the correct diagrams, installation details, and replacement parts.

For model-specific identification tips and documentation, use the 66513049K116 owner’s manual and the 66513049K116 installation guide.

Last updated: February 2026

Yes, it’s usually worth repairing a Kenmore dishwasher like model 66513049K116 when the problem is isolated (drain, heat, fill, latch, rack hardware) and the machine is otherwise cleaning well and not leaking. If you’re facing repeated failures or major tub damage, replacement is the better long-term value.

Quick way to decide (repair vs. replace)

Use this checklist first; it keeps the decision practical and cost-based.

• Repair makes sense when the issue is a single failed part (pump, valve, heater, latch)
• Repair makes sense when the dishwasher is not leaking from the tub or door area
• Replace makes sense when you’ve had multiple repairs in the last 12 to 18 months
• Replace makes sense when the tub is cracked or badly rusted
• Replace makes sense when the control and motor system are both failing

Typical repair “wins” for this model

Symptom	Common fix	Example part for 66513049K116
Won’t drain	Drain pump or drain hose	Dishwasher drain pump WPW10348269
Not heating or poor drying	Heater circuit or thermostat	Element assembly W10518394
Won’t fill	Water inlet valve	Dishwasher water inlet valve WPW10327249
Door won’t latch/start issues	Door latch	Dishwasher door latch WPW10653840

What to check before spending money

We recommend confirming these basics first because they can mimic a “bad part.”

• Verify the dishwasher is installed with a grounded electrical supply and proper clearances
• Confirm the drain hose is routed correctly and not kinked or crushed
• Make sure the unit is level and the door closes squarely
• Clean the filter and spray arms so water flow is strong
• Run the built-in checks and troubleshooting steps in the 66513049K116 owner’s manual

Why it matters

A targeted repair (like a drain pump, inlet valve, or heating element) restores performance and avoids the time and cost of replacing and reinstalling a built-in dishwasher. On the other hand, repeated breakdowns usually mean higher total cost and more downtime.

Last updated: February 2026

For the Kenmore 66513049K116 dishwasher, the most commonly replaced parts are the ones tied to draining, filling, washing performance, heating, and door closing. We see the highest demand for filters, pumps, inlet and drain components, spray arms, and door latch parts; confirm fit and symptoms using the owner's manual.

Commonly replaced parts for this model

These are frequent wear items or failure points that match typical symptoms like not draining, poor cleaning, leaks, or not starting:

• Dishwasher filter W10872845 (clogs can cause poor cleaning and drainage issues)
• Dishwasher drain pump WPW10348269 (won’t drain, humming, standing water)
• Dishwasher water inlet valve WPW10327249 (won’t fill, fills slowly, no wash action)
• Dishwasher drain hose 8269144A (leaks, poor draining, installation-related kinks)
• Dishwasher spray arm WPW10498900 or dishwasher spray arm WPW10491331 (poor cleaning, low spray, clogged jets)
• Dishwasher door latch WPW10653840 (won’t start because the door won’t latch)
• Element assembly W10518394 (water not heating, poor drying)

Quick symptom-to-part guide

Symptom	Parts to check first	Why
Standing water after cycle	Drain hose, drain pump, filter	Most drain problems start with a clog or weak pump
Dishes still dirty	Filter, spray arms	Restricted flow reduces spray pressure
No fill or weak wash	Water inlet valve	Low water level leads to weak circulation
Won’t start	Door latch	The control needs a closed-latch signal
Poor drying	Heating element	Heat boosts drying and helps dissolve detergent

Why it matters

Replacing the right part first saves time and prevents repeat issues. For example, a clogged filter can mimic a bad pump, and a kinked drain hose can look like a drain failure.

Before you order

We recommend these quick checks to avoid buying the wrong part:

• Match the symptom to the cycle step (fill, wash, drain, dry)
• Clean the filter and inspect spray arm holes for debris
• Check the drain hose for kinks and proper routing
• Make sure the door closes firmly and latches
• Use the troubleshooting steps and maintenance guidance in the owner's manual

Last updated: March 2026