Kenmore 11097283110 gas dryer Parts

Your Kenmore dryer’s model number is printed on the appliance’s ID tag; for Kenmore gas dryers like model 11097283110, it’s most often found around the door opening or on the cabinet frame. Once you have the full model number, we can match the correct parts and diagrams.

Check these common locations on Kenmore dryers:

• Inside the dryer door opening on the front frame
• On the door itself (edge or inner panel)
• On the back panel of the dryer cabinet
• Near the lint screen housing (around the opening)
• Behind the lower front access panel (on some designs)

For accurate parts lookup, copy the model number exactly as shown on the tag.

• Use the full number, not just the first three digits (for example, write 11097283110, not just “110”).
• Don’t use numbers from the control panel; use the ID tag only.
• If the tag is worn, take a clear photo and zoom in to confirm each digit.

Kenmore model numbers determine the exact fit for critical gas-dryer components like the igniter, thermal fuse, and gas valve coils. Using the correct model number helps prevent ordering the wrong part and avoids repeat disassembly.

If you are troubleshooting while you locate the tag, these are common model-specific parts we match by model number:

• Thermal fuse WP3390719
• Dryer igniter 279311
• Dryer valve coil kit 279834

Last updated: February 2026

The Kenmore gas dryer model 11097283110 is a full-size, standard-width dryer. Most Kenmore 110-series dryers measure about 27 inches wide, 26 to 29 inches deep, and 43 to 44 inches tall; allow extra space behind the cabinet for the vent and gas line.

These are the most common exterior size ranges for a standard Kenmore 110 gas dryer like model 11097283110:

• Width: ~27 inches
• Height: ~43 to 44 inches (to the top of the cabinet)
• Depth: ~26 to 29 inches (cabinet only)
• Depth with vent hookup: often adds 4 to 6 inches
• Door swing clearance: plan at least 20 to 24 inches in front

Use a tape measure and confirm these three points:

• Measure widest point (usually the cabinet sides, not the door)
• Measure depth from the front panel to the back panel, then add space for the vent elbow
• Measure height to the top rear corner (some installations need clearance for the vent path)

Correct sizing prevents crushed venting (slow drying, overheating) and avoids kinks in the gas connector. Planning for installed depth also helps the dryer sit flush without stressing the exhaust duct.

If you are troubleshooting performance after moving or reinstalling the dryer, use our guide: gas dryer wont heat troubleshooting video.

Last updated: February 2026

The average lifespan of a Kenmore gas dryer like model 11097283110 is about 13 years with normal household use and proper venting. Regular lint removal and fixing airflow or heat issues quickly are the biggest factors in reaching (or exceeding) that service life.

• Venting and airflow: crushed ducting and long runs overheat the dryer and strain parts.
• Lint control: a clogged lint screen or blower housing reduces airflow.
• Heat system health: weak ignition or cycling heat increases run time and wear.
• Drum support and belt drive: worn pulleys and seals add friction and noise.
• Load habits: frequent overloading shortens belt, motor, and drum component life.

• Clean the lint screen every load; replace a damaged screen such as screen W10120998.
• Inspect and clean the exhaust duct; keep the outside hood opening freely.
• If drying times increase, check airflow first, then heat.
• Address overheating symptoms promptly; a failed safety device like thermal fuse WP3390719 often points to a vent restriction.
• If you hear squealing or thumping, inspect the belt path and idler; dryer idler pulley 279640 is a common wear item.

A gas dryer that is forced to run hot or with restricted airflow wears out faster and can repeatedly blow safety fuses. Keeping airflow strong reduces cycle time, protects the motor, and helps the burner system operate normally.

Last updated: March 2026