Owner’s manual
View engine
What year was Craftsman 917288341 made?
Craftsman model 917288341 is typically from the mid-2000s era, and the operator’s manual identifies it as a 21.0 HP, 42-inch mower lawn tractor with electric start and automatic transmission. For the most accurate date range tied to your exact unit, use the model and serial information shown in the 917288341 owner’s manual.
We date Craftsman tractors most accurately by the serial number, not the model number alone. Use these steps:
- Locate the model/serial tag (commonly under the seat, on the frame rail, or near the rear fender area).
- Write down the model number (917288341) and the full serial number.
- Compare the serial format to the identification section in the 917288341 owner’s manual.
- If you are ordering parts, match by model plus serial to avoid deck and drivetrain variations.
- If the tag is missing or unreadable, use the tractor’s configuration (42-inch deck, transmission type, engine family) to narrow it down.
The documentation for this tractor confirms the core configuration for model 917288341.
| Item | What the manual shows |
|---|---|
| Brand | Craftsman |
| Model | 917288341 |
| Mower deck size | 42-inch |
| Starting system | Electric start |
| Transmission | Automatic |
The build year affects parts compatibility because Craftsman tractors can change belt routing, pulleys, mandrel assemblies, and electrical harnesses across production runs. When you match by serial, you reduce the risk of ordering the wrong blade drive belt, deck blade, or starter solenoid.
Last updated: January 2026
How much does it cost to replace a riding lawn mower engine?
Replacing the engine on a Craftsman riding lawn tractor like model 917288341 typically costs about $260 to $1,800 installed, depending on the engine type, labor rates, and whether related items (belts, wiring, fuel system parts) also need service.
- Engine price: New replacement engines vary widely by horsepower, shaft size, and emissions configuration.
- Labor time: Riding mower engine swaps commonly run around 6 hours of shop time.
- Extra parts and supplies: Oil, filter, fuel line, clamps, gaskets, and hardware often add cost.
- Condition of the tractor: Rusted fasteners, damaged wiring, or worn pulleys can increase labor.
- Deck and drive system condition: If belts or mandrels are worn, you may choose to address them while the tractor is apart.
| Cost item | Typical range | Notes |
|---|---|---|
| Engine (part only) | $200 to $1,400 | Varies by HP and spec match |
| Labor | $200 to $600 | Often based on ~6 hours |
| Fluids, tune-up items, misc. hardware | $20 to $150 | Oil, filter, fuel items, fasteners |
| Estimated total installed | $260 to $1,800 | Most common real-world range |
If the engine clicks but will not start, the fix is often electrical, not a full engine replacement. Our troubleshooting steps in the 917288341 owner’s manual point to these common checks:
- Recharge or replace the battery
- Clean and tighten battery terminals
- Check wiring connections
- Test or replace the starter solenoid
- Inspect the starter and starter cable condition
If you’re already diagnosing a click-no-start, the riding lawn mower engine clicks but doesnt turn over video is a good step-by-step walkthrough.
An engine replacement is one of the highest-cost repairs on a riding mower. Confirming the starting system (battery, cables, solenoid, starter) first can prevent spending hundreds on an engine when a smaller part is the real issue.
Last updated: January 2026
What engine does Craftsman riding mower use?
The Craftsman riding mower model 917288341 uses a low-emission gasoline engine; the operator’s manual identifies this tractor as a 21.0 HP, 42-inch mower configuration (HP is rated by the engine manufacturer). For the exact engine make and model, use the identification information in the 917288341 owner's manual.
We recommend matching the engine by its ID tag, not by horsepower alone.
- Turn the engine off, remove the key, and let the engine cool.
- Look for the engine model/type/code label (often on the blower housing, valve cover area, or near the starter).
- Write down the full engine model and code exactly as shown.
- Compare that information to the engine section in the manual and your parts diagrams.
- If you are ordering starting or electrical parts, confirm your wiring layout first.
| Symptom | Most common cause | What to check first |
|---|---|---|
| Clicks but won’t crank | Weak battery, bad connections, solenoid | Battery charge, cable ends, solenoid terminals |
| Cranks but won’t start | Fuel delivery, stale fuel, ignition issue | Fresh fuel, air filter, spark plug |
| Starts then dies when brake released | Safety interlock issue | Brake switch, seat switch, wiring |
If you are chasing a no-crank issue, the lawn tractor starter solenoid 582042802 is a common electrical part involved in the starting circuit on this model.
The same Craftsman tractor model family can be built with different engine variants over time. Using the engine’s model/code prevents ordering the wrong tune-up parts, starter components, or carburetor-related items.
Last updated: January 2026
