Kenmore Elite 11023022100 washer Parts

Most Kenmore washers last 10 to 15 years with normal household use. For your Kenmore Elite washer model 11023022100, keeping loads balanced, using the right water level and temperature settings, and fixing small issues early helps you reach that typical lifespan; see the 11023022100 owner's manual for model-specific care and operating tips.

A washer’s service life depends more on use and maintenance than the brand name on the lid.

• Loads per week: more cycles equals faster wear on the drive system and pump
• Overloading: strains the gear case, clutch, and basket drive
• Out-of-balance spinning: stresses suspension springs and pads
• Water quality: sediment can shorten inlet valve life
• Drain performance: slow draining overworks the drain pump

Your 11023022100 uses a traditional top-load design with features like multiple water level settings and automatic temperature control. When wear shows up, it often appears as agitation or spin problems, draining issues, or excessive vibration.

• Keep the washer level to reduce vibration and suspension wear.
• Use the right water level for the load size (too low increases friction; too high wastes water).
• Avoid packing the basket tight; leave room for clothes to circulate.
• Check fill hoses and screens periodically to protect the inlet valve.
• If draining slows, inspect the drain hose for kinks and clear pump obstructions.

A washer that is maintained and repaired early typically avoids secondary damage (for example, a struggling drain pump can lead to repeated spin issues and extra strain on the drive system). Ordering the correct replacement parts for model 11023022100 from the parts list on this page helps keep repairs straightforward; you can also search by model number on Sears PartsDirect.

Last updated: February 2026

The Kenmore Elite washer model 11023022100 is a KING SIZE capacity top-load washer, but the exact tub volume in cubic feet is not listed in the model’s feature excerpt. Most KING SIZE direct-drive Kenmore top-load washers of this style typically fall in the about 3.2 to 3.5 cu. ft. range; confirm the exact capacity in the 11023022100 owner's manual.

We recommend using the model-specific documentation first, because capacity can vary by basket and tub design.

• Check the specifications section in the 11023022100 owner's manual
• Look for wording such as capacity, tub volume, basket volume, or KING SIZE
• If the manual lists basket dimensions (diameter and depth), you can calculate cubic feet
• If your washer has a replacement basket installed, capacity can differ from the original
• Match your washer’s features (Total Care agitator, porcelain basket) to the manual description to ensure you have the correct document

For Kenmore 110-series, direct-drive, top-load washers with a full-size basket, “KING SIZE” commonly aligns with a mid-to-large traditional top-load capacity.

Knowing the cubic feet helps us choose the right cycle settings and load size. Overloading a smaller-capacity basket can cause poor agitation, out-of-balance spinning, and extra wear on drive components like the washer motor coupling 285753A and gear case 3360629.

You can also order replacement parts for your Kenmore Elite 11023022100 from the parts list for this model, or search by model number on Sears PartsDirect.

Last updated: February 2026

To hard reset your Kenmore Elite washer model 11023022100, unplug the washer (or turn off the breaker) for about 1 minute, then restore power. This clears a temporary control glitch without changing your cycle selector (timer) settings; use the 11023022100 owner's manual for model-specific control details.

• Press Power/Cancel to stop the cycle.
• Unplug the washer (or switch the laundry breaker OFF).
• Wait 60 seconds.
• Restore power.
• Set the Cycle selector (timer) to a normal cycle.
• Close the lid and pull the knob (or press Start, if your console has it) to test.

A reset helps only when the control is confused. If the washer still will not run, these are the most common next checks on this style of Kenmore top-load washer:

• Confirm the lid is fully closed; a lid switch problem can stop spin.
• Make sure the timer knob advances and is not stuck between positions.
• Check for drain issues (standing water can prevent spin).
• Listen for motor sound; a broken coupling can cause no-agitate/no-spin.
• Reduce the load and redistribute items if the tub is off-balance.

A hard reset is a quick way to clear a momentary electrical or control-state issue. If the washer repeatedly needs resets, the underlying problem is usually a lid switch, drain problem, drive system wear, or a timer/control issue.

You can order replacement parts for model 11023022100 from the parts list for this washer, or search by model number on Sears PartsDirect.

Last updated: February 2026

To unclog the drain hose on your Kenmore Elite washer model 11023022100, we recommend unplugging the washer, removing as much water as possible from the tub, then checking both the external drain hose and the drain pump path for lint, coins, or small clothing items. Use the 11023022100 owner's manual for model-specific access and safety notes.

• Unplug the washer before removing panels or hoses
• Turn off both hot and cold water supply valves
• Protect the floor with towels or a shallow pan
• Expect water to spill when hoses are loosened
• Wear gloves; debris and sharp objects are common

1. Drain standing water: Scoop water out, or use a wet/dry vac at the end of the drain hose.
2. Check the standpipe and hose end: Make sure the hose is not shoved too far down the drain pipe; that can restrict flow.
3. Inspect for kinks or pinches: Straighten the hose behind the washer and confirm it is not crushed.
4. Clear the hose: Remove the drain hose and flush it with hot water; push out clogs with a flexible brush or small drain snake.
5. Check the pump inlet: If the hose is clear but the washer still will not drain, inspect the pump inlet and impeller area for obstructions. On this model, a common replacement is the washer drain pump WP3363394.

A restricted drain hose or blocked pump can leave water in the tub, cause poor spin performance, and increase wear on drive components. Clearing the blockage early helps protect the motor coupling and gear case.

You can order model-matched replacement parts from the parts list for 11023022100, or search by model number on Sears PartsDirect.

Last updated: February 2026