Kenmore Elite 11087731701 dryer Parts

To reset your Kenmore Elite dryer model 11087731701, we recommend a hard reset: unplug the dryer (or switch off the breaker) for 1 to 5 minutes, then restore power and try a cycle. If the controls are locked, clear the control lock per the 11087731701 owner's manual.

Quick reset steps (most common)

• Turn the dryer OFF.
• Unplug the power cord (or turn the circuit breaker OFF).
• Wait 1 to 5 minutes.
• Restore power.
• Select a normal cycle and press Start.

If the display shows a lock (LOC/CL) or buttons do not respond

Control lock is a feature, not a failure. Use the control-lock steps listed in the 11087731701 owner's manual. If the panel still will not respond after unlocking, power-cycle again and try a different cycle selection.

If the dryer still will not start after a reset

A reset will not fix a failed safety device or airflow problem. These checks solve most “won’t start” complaints:

• Confirm the dryer has full power (electric dryers typically need 240V; a tripped breaker can leave the motor dead).
• Make sure the door closes firmly; a weak latch can prevent starting.
• Clean the lint screen and check the vent for restrictions.
• Listen for abnormal squealing or thumping; a seized drum support or idler can stall the motor.
• If the dryer runs but heat is inconsistent, a temperature-sensing issue can cause odd cycling.

Parts that commonly relate to these symptoms

Symptom	Common cause	Example part for this model
Door won’t “click” shut	Worn latch	Catch 279570
Loud rumble/squeal	Worn rollers/idler	Dryer repair kit 4392067
Heat cycles oddly	Sensor/thermistor issue	Dryer thermistor WP8577274

Why it matters

Resetting clears temporary control glitches, but dryers also stop for safety reasons (overheating risk, door not shut, motor overload). Fixing airflow and worn moving parts helps the dryer start reliably and dry faster.

Last updated: January 2026

Kenmore Elite dryer model 11087731701 is a full-size, extra-large capacity dryer; it is typically listed at about 7.5 cu. ft. Capacity and exact cabinet dimensions for your specific configuration are shown in the 11087731701 owner's manual.

Typical size specs you can expect

Most Kenmore Elite 110-series full-size dryers fall into these common ranges:

Spec	Typical value/range	What it affects
Capacity	~7.0 to 7.5 cu. ft.	Load size, cycle time
Width	~27 in.	Fit in standard laundry alcoves
Height	~38 to 39 in.	Clearance under shelves/cabinets
Depth	~30 to 32 in.	Closet fit, door clearance

How we recommend measuring for a perfect fit

• Measure width across the front of the cabinet (not the door).
• Measure height from the floor to the top of the cabinet.
• Measure depth front-to-back; note if the door or controls protrude.
• Add 4 to 6 inches behind the dryer for the exhaust duct and power cord.
• Confirm the door swing space so the door opens fully.

Why it matters

Correct sizing prevents a tight install that kinks the exhaust duct (long dry times), blocks airflow (overheating), or leaves too little clearance for electrical connections and routine lint cleaning.

Last updated: January 2026

On Kenmore Elite dryer model 11087731701, the model number is printed on the rating label. You will typically find that label on the door opening (cabinet frame) when you open the dryer door, or on the back of the dryer near the top.

Most common places to check

• Open the dryer door and look around the door opening on the cabinet frame
• Check the inside edge of the door itself
• Look on the back panel near the top of the dryer
• If your dryer has a lower access panel, check just inside that area for an additional label

What the label looks like

The label usually includes the model number (11087731701) and often the serial number. It may also list electrical information and the brand name (Kenmore).

Location	How to spot it	Why it helps
Door opening (cabinet frame)	Sticker or metal tag visible with door open	Fastest way to confirm the exact model
Back of dryer (near top)	Label on rear panel	Helpful if the door label is worn
Inside door edge	Label along the door perimeter	Common on some Kenmore designs

Why it matters

Using the exact model number ensures we match the correct Kenmore Elite dryer parts and diagrams for your unit, especially for fit-critical items like a dryer heating element WP8544771 or a drum support roller.

Next step after you find it

• Write down the full model number exactly as shown
• Use the model number to confirm compatible parts and troubleshooting steps
• For additional identification details and safety information, reference the 11087731701 owner's manual

Last updated: January 2026