Owner’s manual
How to look up chainsaw serial number?
On the Craftsman 358355162 gas chainsaw, the serial number is typically stamped into the engine/motor housing or crankcase on a flat spot near the muffler area. Once you find it, record it exactly as shown (letters, numbers, and any dashes).
Where to check on the saw
Look for a stamped or printed ID on a flat surface of the powerhead:
- On the left or right side of the engine housing when viewing the saw from the top
- Near the muffler area (common location)
- On the crankcase area of the powerhead
- On an ID label or plate if your unit uses a decal instead of a stamp
For diagrams and model identification details, use the 358355162 owner's manual.
How to read and use the serial number
Serial numbers can be easy to misread, so we recommend:
- Wipe off oil and sawdust first; use a flashlight at an angle
- Write it down and also take a photo for reference
- Double-check similar characters (0 vs O, 1 vs I)
- Keep it with your model number 358355162 for parts lookup and service
Quick checklist
| Item | What to capture | Why it matters |
|---|---|---|
| Model number | 358355162 | Identifies the correct parts diagrams |
| Serial number | Exact stamped/printed code | Helps match production version and service info |
Why it matters
On chainsaws, small production changes can affect parts fit (fuel system pieces, starter components, bar and chain setups). Having the correct serial number helps ensure you match the right Craftsman chainsaw parts the first time.
Last updated: January 2026
Where is the model number on a chainsaw?
On the Craftsman chainsaw model 358355162, the model number is typically found on the product identification label or ID tag on the saw body (powerhead). Check the label area near the rear handle, starter housing, or fuel tank area, then match the number exactly when ordering parts.
Common places to check on a Craftsman gas chainsaw
Look for a printed label, stamped plate, or tag on the powerhead. On many saws, it is located in one of these spots:
- Near the rear handle or control handle area
- On or near the starter housing (recoil starter side)
- Around the fuel cap and fuel tank area
- Near the bar clamp side of the saw body
- On the underside of the saw where debris is less likely to rub it off
If the label is dirty, wipe it with a damp rag and a little mild cleaner; avoid scraping hard enough to remove printing.
What to write down (so you get the right parts)
For parts lookup and diagrams, we recommend recording these details exactly as shown:
- Model number (for this saw: 358355162)
- Any type or product number listed on the same tag (if present)
- The brand (Craftsman)
- The serial number (helpful for production variations)
Quick ID checklist
Use this checklist to confirm you have the correct identifier:
| Item on label | What it’s used for | Example |
|---|---|---|
| Model number | Matching parts diagrams and fit | 358355162 |
| Serial number | Identifying production run | Varies |
| Bar length info | Choosing bar and chain | 14-in or 16-in (varies) |
Why it matters
Chainsaws often have multiple versions that look similar but use different fuel lines, bars, chains, or carburetor parts. Using the exact model number helps ensure the replacement part fits and performs correctly.
For diagrams and additional identification notes, use the 358355162 owner’s manual.
Last updated: January 2026
What model number is a Craftsman 358355162 16 36cc chainsaw?
The model number for your Craftsman gas chainsaw is 358355162. On this model, the model number is the key identifier we use to match the correct parts (like the guide bar and chain) and the correct operating and maintenance instructions in the 358355162 owner's manual.
Where to find the model number on the saw
Most Craftsman chainsaws list the model number on a data label on the powerhead. Check these common spots:
- Near the rear handle or control handle area
- On the starter housing (recoil cover) side
- Near the fuel cap and oil cap area
- On the crankcase or chassis label plate
Why the model number matters for parts fit
Even when two saws are both “16-inch, 36cc,” small design differences can change what fits (bar mount pattern, chain pitch, drive link count, clutch drum, oiler setup). Using 358355162 helps ensure you get compatible parts.
| What you are matching | What to use | Example for this model |
|---|---|---|
| Parts diagrams and part lists | Model number | 358355162 |
| Guide bar fit | Bar part ID | Bar 160SDEA041 |
| Chain fit | Chain part ID | Chain 91PX056G |
Quick checks before ordering a bar or chain
Use the saw’s current bar and chain markings plus the manual specs to confirm fit:
- Bar length (commonly 16-inch on this configuration)
- Chain pitch and gauge (stamped on the bar or listed in the manual)
- Drive link count (count links or match the number on the chain package)
- Bar mount pattern (must match the powerhead)
- Condition of the sprocket and bar rails (worn parts can cause poor cutting)
Why it matters
Ordering by the correct model number prevents common issues like a chain that will not tension correctly, a bar that will not mount, or a chain that does not match the sprocket. The 358355162 owner's manual also covers safe operation and maintenance intervals that help extend bar, chain, and clutch life.
Last updated: January 2026
Is 40 1 or 50 1 better for chainsaws?
For the Craftsman 358355162 gas chainsaw, we use a 40:1 gas-to-oil mix because the operator guidance for fueling specifies Poulan or Weed Eater 40:1 engine oil and gives 40:1 mixing amounts (3.2 oz oil per 1 gallon gas). That ratio delivers the lubrication this 2-cycle, air-cooled engine is designed to run on.
What to mix (40:1 amounts)
Use fresh regular unleaded gasoline and a quality 2-cycle, air-cooled engine oil.
- 40:1 = 3.2 oz oil per 1 gallon gasoline
- Mix fuel in an approved container, not in the fuel tank
- Shake or stir thoroughly; gas and oil do not combine easily
- Too much oil can foul the spark plug
- Too little oil (or the wrong oil) can overheat and seize the engine
| Mix ratio | Oil per 1 gallon gas | What it changes |
|---|---|---|
| 40:1 | 3.2 oz | More lubrication margin for air-cooled 2-cycle engines |
| 50:1 | 2.6 oz | Less oil; not a good match when the saw is set up for 40:1 |
When 50:1 makes sense (and when it does not)
Some newer chainsaws are engineered for 50:1 with specific oils. On the 358355162, using 50:1 reduces lubrication compared to the 40:1 mix the fueling instructions call out, especially during long cuts, hot weather, or when the chain is dull.
Related maintenance that affects how the saw runs
- Keep the chain sharp and properly tensioned to avoid overloading the engine
- If the saw runs lean or surges, inspect fuel delivery parts like the fuel assembly 530095646
- If fuel lines are cracked or leaking, replace them and related fittings such as the oil line 530069216
Why it matters
Correct mix ratio is a top factor in 2-cycle engine life; it controls lubrication, operating temperature, and carbon buildup.
For the exact cautions and fueling steps, follow the Craftsman 358355162 owner’s manual.
Last updated: January 2026
