Samsung DVE60M9900V/A3-00 dryer Parts

On the Samsung DVE60M9900V dryer, we clear many temporary error (information) codes by power-cycling the dryer (turn it off, then remove power briefly). If the same code comes back, the dryer is detecting a real condition (like airflow restriction, door issue, or a sensor problem) that needs troubleshooting, not repeated resets.

• Press POWER to turn the dryer off.
• Unplug the dryer for 1 to 5 minutes (or switch the dryer breaker OFF for 1 to 5 minutes).
• Restore power.
• Start a simple cycle (for example, TIME DRY) and see if the code returns.
• If the code returns immediately, stop the cycle and troubleshoot the cause.

Your DVE60M9900V manual lists common information codes and the first checks to perform. See the DVE60M9900V user manual.

Here are high-value checks that fix many repeat codes:

• Clean the lint filter and make sure it is seated correctly.
• Check the venting for kinks, crushed duct, or a blocked outside hood.
• Confirm the door closes firmly and no laundry is caught in the door opening.
• Avoid overloading; heavy loads can trigger moisture and temperature related codes.
• Verify power supply is stable (especially after storms or breaker trips).

Clearing the code gets the control board out of “alarm” mode, but the dryer will keep protecting itself if it still senses overheating, restricted airflow, or a sensor/door problem. Fixing the root cause helps prevent long dry times, no-heat symptoms, and repeat shutdowns.

• For a broader list of Samsung dryer codes and fixes, use our Samsung dryer error codes resource.
• If your dryer uses Smart Care diagnostics, our Samsung smart care dryer error codes guide can help you interpret app-based results.

Last updated: January 2026

No. A Samsung DVE60M9900V electric dryer is designed for a 120/240V (or sometimes 120/208V) supply; plugging it into 110V or 120V will not provide enough power for the heater and can cause unsafe wiring overheating or nuisance breaker trips. Use the correct dedicated dryer circuit.

• Install a dedicated 30-amp dryer circuit with the correct receptacle for your cord type (3-prong or 4-prong).
• If your home has only 120V laundry power available, choose a 120V dryer or a gas dryer (if gas service and venting are available).
• If you are moving into a new place, confirm the laundry outlet type before delivery.
• If you are unsure whether your unit is configured as gas or electric, check the data label and the electrical requirements section in the DVE60M9900V user manual.
• Avoid “adapter” solutions; they do not create the required 240V supply and can create a fire hazard.

Most of the energy an electric dryer uses is for the heating element. On 120V, the dryer cannot deliver the wattage needed to heat properly, so you typically get:

• No heat or very weak heat
• Extremely long dry times
• Higher current draw on an undersized circuit (overheating risk)
• Potential damage to wiring, cord, terminal block, or control components

Correct voltage and a dedicated circuit protect the dryer’s heater circuit, motor, and controls, and they reduce the risk of overheating at the outlet, cord, and terminal connections.

Last updated: January 2026

On the Samsung DVE60M9900V dryer, “E3” is not one of the documented information codes in the model’s manual, so we can’t map it to a single, model-specific failure from the official code table. In practice, treat it as a display-variation code and start with airflow, load, and reset checks.

Samsung displays can look similar (for example, “E3” vs “3E”, “tC”, “HC”, or “9C1”). Before replacing parts, we recommend verifying the exact characters on the display and whether the code appears on the Delicate Dryer or the Tumble Dryer.

• Write down the code exactly as shown (letters, numbers, and any “1” prefix).
• Note which section is running (Delicate Dryer top compartment vs Tumble Dryer drum).
• Power the dryer off, then back on, and see if the same code returns.
• Check for a second code after restarting a cycle.

These steps are safe and align with the DVE60M9900V troubleshooting and maintenance guidance in the DVE60M9900V user manual.

• Clean the lint filter before restarting.
• Reduce the load size; run a small load to confirm normal tumbling.
• Check the exhaust hood outside; it should open freely.
• Inspect the vent for kinks, crushing, or heavy lint buildup.
• Reset power: unplug (or switch off the breaker) for 5 minutes.

This model includes a Vent Blockage Test that reports “0” for normal venting or “CLg” for restricted venting.

Many Samsung dryer codes are triggered by restricted airflow or abnormal operating conditions; fixing venting and load issues can prevent overheating, long dry times, and repeat shutdowns.

For broader code naming variations across Samsung dryers, we also use our Samsung dryer error codes reference.

Last updated: January 2026