Kenmore 2213229N414 dishwasher Parts

On Kenmore dishwasher model 2213229N414, we find the model number on the rating label located just inside the dishwasher door opening, typically along the left-hand side of the tub frame. The same label usually lists the serial number.

• Open the dishwasher door fully.
• Look along the left inner edge of the tub opening (the vertical frame area).
• Check the top edge of the tub opening if you do not see it on the side.
• Wipe the area with a damp cloth; labels can be hard to read under residue.
• Use a flashlight and take a photo to zoom in on small print.

Most Kenmore dishwashers place key ID details together on the same rating label:

Using the exact model number (including every letter and digit) ensures we match the correct Kenmore parts for your dishwasher, such as a door seal, rack adjuster, or drain pump. It also helps when you reference procedures and diagrams in the owner's manual.

• Check the right-hand side of the tub opening as a secondary location.
• Look for a second label on the door edge itself.
• If the label is damaged, use the clearest characters you can read and compare them to the format shown in the owner's manual.

Last updated: February 2026

Common problems on the Kenmore 2213229N414 dishwasher are no-start conditions (door not fully latched or control lock on), poor cleaning from restricted water flow or clogged wash components, draining problems, and leaks caused by suds or worn seals. The troubleshooting steps in the owner's manual cover the fastest checks.

• Dishwasher will not run: door not closed and latched, Start/Resume sequence not completed, Control/Lock enabled, no power (tripped breaker).
• Detergent left in the dispenser: door not fully latched, items blocking the dispenser, cycle interrupted.
• Poor cleaning: clogged filter, blocked spray nozzles, low incoming water temperature, loading issues.
• Not draining: drain path restriction, drain hose issue, failing drain pump.
• Leaking: unit not level, oversudsing from wrong detergent, worn door seals.

1. Close the door firmly; if the Start/Resume light is blinking, press START/RESUME and close the door within 3 seconds.
2. Confirm Control/Lock is off and a cycle is selected.
3. Verify power at the breaker.
4. Use only dishwasher detergent; measure accurately to prevent suds overflow.
5. Confirm incoming hot water is about 120°F (49°C) for best cleaning and drying.

Most “big” dishwasher complaints trace back to a few basics: the door must latch, water must enter at the right temperature and pressure, and the wash system must circulate and drain freely. Fixing those fundamentals prevents repeat clogs, leaks, and poor wash results.

Last updated: February 2026

Yes, repairing a Kenmore dishwasher like model 2213229N414 is worth it when the problem is a common wear item (rack parts, seals, hoses, valves) and the unit otherwise cleans well and runs reliably. Replacement makes more sense when repairs are frequent or the tub and motor system has major recurring failures.

Use this checklist first:

• The dishwasher is cleaning well after basic maintenance (filter cleaning, correct loading, fresh detergent).
• The issue is isolated to one symptom (leak, not draining, not filling, rack not rolling).
• The repair is a straightforward part swap (seal, drain hose, inlet valve, drain pump).
• The door closes and latches normally, and the racks slide smoothly.
• You are not seeing repeated electrical/control problems.

These are common, targeted fixes that often restore normal operation:

• Leaks at the door: replace the tub gasket W11177741 or the dishwasher door seal, lower W10909089
• Not draining: check the drain path and consider the dishwasher drain pump W10876537
• Not filling: test water supply and consider the dishwasher water inlet valve W11175771
• Poor drying: inspect the heating circuit and consider the element assembly W10703867
• Rack problems: replace the dishwasher rack adjuster W10712395 or wheels/track stops

A dishwasher repair is most valuable when it solves the root cause (leak source, drain restriction, fill failure) and prevents secondary damage like water on the floor, poor wash results, or repeated cycle interruptions. Your owner's manual also includes troubleshooting guidance that helps you confirm the failure before ordering parts.

Last updated: February 2026

In a Kenmore 2213229N414 dishwasher, the most commonly replaced parts are the ones that handle water flow, heating, sealing, and rack movement. When you see leaks, poor cleaning, or draining problems, parts like the inlet valve, drain pump, heating element, and door seals are the first places we check; see the owner's manual for model-specific care and troubleshooting.

• Water inlet valve: fills the tub; failures cause no-fill or slow-fill issues (example: dishwasher water inlet valve W11175771)
• Drain pump: pushes water out; failures cause standing water (example: dishwasher drain pump W10876537)
• Heating element: heats water and helps drying; failures cause poor drying or cooler washes (example: element assembly W10703867)
• Door seals and gaskets: prevent leaks at the door and tub edge (example: tub gasket W11177741)
• Spray arm: drives wash performance; clogs and wear cause poor cleaning (example: dishwasher spray arm, lower WPW10491331)
• Racks and rack hardware: wheels, adjusters, and stops wear and break (example: dishwasher rack adjuster W10712395)

These components do the most work every cycle. Heat, detergent, hard-water mineral buildup, and food debris gradually cause clogs, warping, cracking, or loss of sealing, which shows up as leaks, noise, weak spray, or drain problems.

• Turn off power at the breaker and shut off the water supply.
• Clean the filter area and check spray arm holes for debris.
• Inspect the door seal surfaces for food residue and gaps.
• Check the drain hose routing for kinks and confirm a high loop.
• Run a short cycle and verify the tub fills with water early in the cycle (a basic operational check noted in the installation instructions).

Last updated: February 2026