Maytag MTW5740TQ0 washer Parts

The Maytag MTW5740TQ0 top-load washer has a 3.2 cu. ft. capacity. This is the tub volume the washer is designed to handle; using the right load size helps cleaning performance, spin-out, and reduces wear on drive components.

How to use that capacity in real life

A 3.2 cu. ft. top-load washer is best when you load by basket fullness, not by weight.

• Fill the basket loosely to about 3/4 full for most mixed loads
• Keep bulky items (blankets, jackets) to 1-2 pieces at a time
• Leave space at the top so items can circulate and agitate
• Distribute items evenly around the basket to reduce out-of-balance spinning
• If the washer bangs or walks, reduce the load and re-balance the items

Quick load-size guide (typical)

Load type	What it usually looks like in the basket	Best practice
Small	Bottom covered, items move freely	Good for delicates and quick washes
Medium	About 1/2 full	Best everyday performance
Large	About 3/4 full	Avoid packing; keep items loose
Bulky	Fewer large items, uneven shapes	Wash 1-2 items; balance carefully

Why it matters

Overloading a 3.2 cu. ft. washer can cause poor agitation and rinsing, longer drain times, and more vibration. Those conditions can speed up wear on parts like the clutch 285785, washer lid switch assembly WP8318084, and washer drain pump WP3363394.

Where to confirm model-specific specs

For the exact specifications and cycle guidance for your MTW5740TQ0, we recommend checking the MTW5740TQ0 owner's manual.

You can also order replacement parts for your MTW5740TQ0 from the parts list for this model, or search by model number on Sears PartsDirect.

Last updated: February 2026

To reset the lid lock on your Maytag MTW5740TQ0 washer, we start with a power reset: unplug the washer for 5 minutes, plug it back in, then close the lid and try a Spin or Drain/Spin cycle. If the washer still will not spin, the lid switch circuit is likely not being made.

Quick reset steps (in order)

• Stop the cycle: push in the timer knob to pause.
• Power cycle: unplug for 5 minutes, then plug into a grounded 3-prong outlet.
• Close the lid firmly: the washer will not agitate or spin with the lid open.
• Restart: pull out the timer knob to start.
• Try a different cycle: select Spin (or a full cycle) and listen for the lid switch “click.”

For model-specific operating steps and cycle behavior, follow the MTW5740TQ0 owner's manual.

When a “reset” does not fix it

On the MTW5740TQ0, a lid lock complaint is often really a lid switch problem. If the washer fills but will not agitate or spin, or stops when the lid is moved, the switch assembly is the first part we check.

Common causes:

• Lid not closing squarely (hinge or lid strike misalignment)
• Broken lid switch actuator tab
• Failed switch contacts inside the assembly
• Loose wiring connection at the lid switch

Part to check first

Symptom	Most likely check	Part on this model page
Won’t spin or agitate, lid must be closed	Lid switch not sensing closed lid	Washer lid switch assembly WP8318084
Stops mid-cycle when lid is bumped	Intermittent lid switch	Washer lid switch assembly WP8318084

Why it matters

The lid switch is a safety interlock. If it does not read “lid closed,” the washer can pause, refuse to spin, or act like it is stuck even though the timer advances.

Ordering the right replacement

We recommend ordering by model number (MTW5740TQ0) to ensure the correct revision. You can order parts from the list for this model, or search by model on Sears PartsDirect.

Last updated: February 2026

For the Maytag MTW5740TQ0 washer, the most common customer-reported issues are won’t drain or spin, won’t start/agitate, and leaks or unusual noises. Many of these trace back to basic checks (lid closed, drain height, suds level) and a few high-wear parts.

Most common symptoms and what usually causes them

• Won’t drain or won’t spin: clogged/kinked drain hose, excessive suds, or a failing drain pump
• Won’t run, fill, rinse, or agitate: lid not closed, a normal cycle pause, overload, or a lid switch problem
• Stops mid-cycle: normal pause (about 2 minutes on some cycles), overload, or power interruption
• Leaks: loose fill hoses, worn tub gasket, or a valve that does not shut fully
• Grinding, squealing, or banging: clutch/brake wear, suspension issues, or a worn drive block

For model-specific operating checks (including lid-closed operation and drain-hose height guidance), use the MTW5740TQ0 owner's manual.

Quick checks we recommend first (fast, no parts)

• Confirm the washer is plugged into a grounded outlet and the breaker is not tripped.
• Close the lid fully; this model will not agitate or spin with the lid open.
• Check drain hose routing; the hose end should not be higher than 96 in. (244 cm) above the floor.
• Reduce detergent if you see excessive suds (suds can prevent proper draining/spinning).
• Wash smaller loads and redistribute bulky items to prevent out-of-balance conditions.

Parts that commonly fix these problems on MTW5740TQ0

If the quick checks do not resolve the issue, these parts are frequent fixes for the symptoms above:

Symptom	Common fix part	What it affects
Won’t spin/agitate with lid closed	Washer lid switch assembly WP8318084	Confirms lid is closed so the washer can run/spin
Won’t drain or drains slowly	Washer drain pump WP3363394	Pumps water out during drain/spin
Poor spin, burning smell, noisy spin	Clutch 285785	Transfers power for spin and helps control basket speed
Agitator not moving properly	Agitator dog 80040	Helps the agitator “ratchet” and move clothes

Why it matters

Drain and spin problems can look like a major failure, but on the MTW5740TQ0 they are often caused by installation conditions (drain height), oversudsing, or a safety interlock (lid switch). Fixing the root cause prevents repeat stoppages and reduces wear on the drive system.

To order replacement parts for your MTW5740TQ0, use the parts list for this model or search by model number on Sears PartsDirect.

Last updated: February 2026

Most Maytag washers average 10 to 13 years of service life in normal household use. For your Maytag MTW5740TQ0 top-load washer, consistent maintenance and avoiding overloads are the biggest factors that keep the drive system, drain pump, and suspension working longer (see the MTW5740TQ0 owner's manual).

Typical lifespan ranges (what we see most often)

• Light use (1 to 3 loads/week): 12 to 15 years
• Average use (4 to 7 loads/week): 10 to 13 years
• Heavy use (8+ loads/week): 7 to 10 years

Usage pattern	Typical lifespan	Biggest wear areas
Light	12 to 15 years	Hoses, lid switch, minor leaks
Average	10 to 13 years	Drain pump, clutch, suspension
Heavy	7 to 10 years	Drive components, basket/drive block, gear case

What shortens washer life fastest

• Overloading (extra strain on the clutch, drive block, and basket drive)
• Unbalanced loads (accelerates wear on suspension springs and pads)
• Detergent overuse (soap buildup, odors, poor rinsing)
• Ignoring slow drains (pump strain and standing water issues)
• Skipping basic cleaning (residue leads to smells and performance problems)

Parts that commonly extend life when replaced

If the washer still fills and drains but performance is slipping, these model-matched parts are common fixes:

• Washer drain pump WP3363394 (won’t drain, slow drain, humming)
• Washer lid switch assembly WP8318084 (won’t spin or stops mid-cycle)
• Clutch 285785 (weak spin, burning smell, poor agitation/spin transfer)
• Agitator dog 80040 (agitator slips or doesn’t move clothes well)

Why it matters

Knowing the expected lifespan helps you decide whether to repair or replace. On a washer in the 10 to 13 year range, a targeted repair like a drain pump or lid switch often restores reliable operation without the cost of a full replacement.

Helpful maintenance habits

• Keep loads evenly distributed and avoid packing the tub tight
• Use the correct water level and cycle for the load
• Periodically run a cleaning routine described in the MTW5740TQ0 owner's manual
• Order model-specific replacement parts from the parts list for MTW5740TQ0, or search by model on Sears PartsDirect

Last updated: February 2026