Kenmore 66514429N510 dishwasher Parts

Yes. We still supply replacement parts for many Kenmore dishwashers, including Kenmore model 66514429N510. The key is matching parts by your full model number so you get the correct fit for common repairs like draining issues, poor cleaning, or heating problems; use the 66514429N510 owner's manual to confirm part locations and access steps.

How to find the right part for your Kenmore dishwasher

Use your model number (66514429N510) first, then match the symptom to the part category.

• Confirm the model number from the rating label on the dishwasher frame (inside the door)
• Identify the symptom (not draining, not filling, not drying, leaking)
• Compare the part name and part ID before ordering
• Replace worn seals, filters, and hoses early to prevent bigger failures
• Follow electrical and installation safety steps in the 66514429N510 installation guide

Common parts people replace on model 66514429N510

These are frequent wear items and failure points on many Kenmore 665-series dishwashers.

Symptom	Likely part area	Example part for this model
Dishes not drying, water not heating	Heater circuit	Element assembly W10518394
Dishwasher will not fill or fills slowly	Water supply valve	Dishwasher water inlet valve (W11175771)
Dishwasher will not drain	Drain system	Dishwasher drain pump (W10876537)
Poor wash, weak spray	Wash system	Dishwasher spray arm (WPW10491331)
Odor, debris left behind	Filtration	Dishwasher filter (WPW10463906)

Why it matters

Ordering by model number prevents returns and downtime. Kenmore dishwashers often share designs with major manufacturers, so the correct match comes from the model-based parts list, not the brand name alone.

Last updated: February 2026

Yes, repairing a Kenmore dishwasher like model 66514429N510 is usually worth it when the problem is a common wear item (drain, fill, heating, leaks) and the repair cost stays well below the price of a replacement; it is less worthwhile when multiple major components fail at once.

Quick way to decide (cost vs. value)

Use this simple rule of thumb for 66514429N510:

• Worth repairing: one clear failure, no rusted tub, no repeated leaks
• Consider replacing: multiple failures, chronic leaking, or major electrical issues plus other symptoms
• Best value DIY repairs: clogs, hoses, filters, spray arm, inlet valve, drain pump

What you’re fixing	Typical repair difficulty	Usually worth it?
Drain problem (won’t drain)	Medium	Yes
No fill / slow fill	Medium	Yes
Poor cleaning (low spray)	Easy to medium	Yes
No heat / poor drying	Medium	Often
Control or wiring issues	Medium to hard	Sometimes

What we check first (fast troubleshooting)

The installation guide’s “If Dishwasher Does Not Operate” checks are the fastest way to avoid unnecessary parts and service:

• Confirm the breaker/fuse is OK
• Make sure the door is fully closed and latched
• Verify the cycle was set correctly
• Confirm the water supply is turned on
• Run the shortest cycle and check for water in the tub after ~2 minutes (then unlatch, wait 5 seconds, open)

For model-specific operating and cycle details, use the 66514429N510 installation guide.

Parts that commonly make a repair “worth it”

If symptoms match, these are high-impact repairs on this model:

• Not draining or humming at end of cycle: dishwasher drain pump W10876537
• Not filling or filling slowly: dishwasher water inlet valve W11175771
• Poor drying or no heat (and other causes ruled out): element assembly W10518394

Why it matters

Dishwashers are designed to run long cycles and pause to let detergent work; that means many “performance” complaints are actually loading, maintenance, or a single worn part, not a full replacement situation. A targeted repair restores cleaning and drying without the cost and hassle of a new install.

Last updated: February 2026

The model number for your Kenmore dishwasher is printed on the appliance’s model and serial tag. On most Kenmore built-in dishwashers like model 66514429N510, you will find that tag on the tub frame around the door opening when you open the door.

Where to look on the dishwasher

Check these common locations in this order:

• Along the left or right side of the tub opening (door frame)
• On the top edge of the tub opening, just under the countertop lip
• On the inner edge of the door itself (near the latch area)
• Behind the lower access panel (kickplate), if the tag is not on the tub frame

If you are removing the lower access panel during installation or service, follow the safety and access steps in the installation guide.

What the model tag looks like

The tag is usually a small sticker or metal plate with multiple lines of text.

• Model: the full model number (example format: 665.14429N510 or 66514429N510)
• Serial: a longer serial number used for manufacturing date and production run
• Electrical ratings: voltage and amperage information

Model number formatting tips

You see on the tag	Use for parts lookup
665.14429N510	66514429N510
66514429N510	66514429N510

Why it matters

Using the exact model number ensures we match the correct Kenmore diagrams and manufacturer-approved parts (for example, a dishwasher water inlet valve W11175771 or dishwasher drain pump W10876537) so the fit and connections are right for your dishwasher.

Last updated: March 2026