Can you still get parts for a Kenmore dishwasher?
Yes. We still supply replacement parts for many Kenmore dishwashers, including Kenmore model 66514429N510. The key is matching parts by your full model number so you get the correct fit for common repairs like draining issues, poor cleaning, or heating problems; use the 66514429N510 owner's manual to confirm part locations and access steps.
Use your model number (66514429N510) first, then match the symptom to the part category.
- Confirm the model number from the rating label on the dishwasher frame (inside the door)
- Identify the symptom (not draining, not filling, not drying, leaking)
- Compare the part name and part ID before ordering
- Replace worn seals, filters, and hoses early to prevent bigger failures
- Follow electrical and installation safety steps in the 66514429N510 installation guide
These are frequent wear items and failure points on many Kenmore 665-series dishwashers.
| Symptom | Likely part area | Example part for this model |
|---|---|---|
| Dishes not drying, water not heating | Heater circuit | Element assembly W10518394 |
| Dishwasher will not fill or fills slowly | Water supply valve | Dishwasher water inlet valve (W11175771) |
| Dishwasher will not drain | Drain system | Dishwasher drain pump (W10876537) |
| Poor wash, weak spray | Wash system | Dishwasher spray arm (WPW10491331) |
| Odor, debris left behind | Filtration | Dishwasher filter (WPW10463906) |
Ordering by model number prevents returns and downtime. Kenmore dishwashers often share designs with major manufacturers, so the correct match comes from the model-based parts list, not the brand name alone.
Last updated: February 2026
Is it worth repairing a Kenmore dishwasher?
Yes, repairing a Kenmore dishwasher like model 66514429N510 is usually worth it when the problem is a common wear item (drain, fill, heating, leaks) and the repair cost stays well below the price of a replacement; it is less worthwhile when multiple major components fail at once.
Use this simple rule of thumb for 66514429N510:
- Worth repairing: one clear failure, no rusted tub, no repeated leaks
- Consider replacing: multiple failures, chronic leaking, or major electrical issues plus other symptoms
- Best value DIY repairs: clogs, hoses, filters, spray arm, inlet valve, drain pump
| What you’re fixing | Typical repair difficulty | Usually worth it? |
|---|---|---|
| Drain problem (won’t drain) | Medium | Yes |
| No fill / slow fill | Medium | Yes |
| Poor cleaning (low spray) | Easy to medium | Yes |
| No heat / poor drying | Medium | Often |
| Control or wiring issues | Medium to hard | Sometimes |
The installation guide’s “If Dishwasher Does Not Operate” checks are the fastest way to avoid unnecessary parts and service:
- Confirm the breaker/fuse is OK
- Make sure the door is fully closed and latched
- Verify the cycle was set correctly
- Confirm the water supply is turned on
- Run the shortest cycle and check for water in the tub after ~2 minutes (then unlatch, wait 5 seconds, open)
For model-specific operating and cycle details, use the 66514429N510 installation guide.
If symptoms match, these are high-impact repairs on this model:
- Not draining or humming at end of cycle: dishwasher drain pump W10876537
- Not filling or filling slowly: dishwasher water inlet valve W11175771
- Poor drying or no heat (and other causes ruled out): element assembly W10518394
Dishwashers are designed to run long cycles and pause to let detergent work; that means many “performance” complaints are actually loading, maintenance, or a single worn part, not a full replacement situation. A targeted repair restores cleaning and drying without the cost and hassle of a new install.
Last updated: February 2026
How do I find the model number on my 66514429N510?
The model number for your Kenmore dishwasher is printed on the appliance’s model and serial tag. On most Kenmore built-in dishwashers like model 66514429N510, you will find that tag on the tub frame around the door opening when you open the door.
Check these common locations in this order:
- Along the left or right side of the tub opening (door frame)
- On the top edge of the tub opening, just under the countertop lip
- On the inner edge of the door itself (near the latch area)
- Behind the lower access panel (kickplate), if the tag is not on the tub frame
If you are removing the lower access panel during installation or service, follow the safety and access steps in the installation guide.
The tag is usually a small sticker or metal plate with multiple lines of text.
- Model: the full model number (example format: 665.14429N510 or 66514429N510)
- Serial: a longer serial number used for manufacturing date and production run
- Electrical ratings: voltage and amperage information
| You see on the tag | Use for parts lookup |
|---|---|
| 665.14429N510 | 66514429N510 |
| 66514429N510 | 66514429N510 |
Using the exact model number ensures we match the correct Kenmore diagrams and manufacturer-approved parts (for example, a dishwasher water inlet valve W11175771 or dishwasher drain pump W10876537) so the fit and connections are right for your dishwasher.
Last updated: March 2026





