Whirlpool WRS325FDAB01 refrigerator Parts

The Whirlpool WRS325FDAB01 side-by-side refrigerator is typically listed at about 25.4 cu. ft. total capacity. Capacity can vary slightly by configuration, so we recommend confirming the exact spec in the WRS325FDAB01 owner's manual.

How to confirm the capacity for your exact unit

We use the manual because it ties the specification to your exact model number and configuration.

• Check the Specifications section in the WRS325FDAB01 owner's manual
• Look for wording such as total capacity, refrigerator capacity, and freezer capacity
• Compare the model number on your rating label to WRS325FDAB01 (inside the fresh food compartment)
• If you are measuring usable space, remember shelves, bins, and the ice maker reduce usable volume

Capacity terms you may see (and what they mean)

Term	What it includes	Why it matters
Total capacity	Fresh food + freezer	Best for comparing models overall
Refrigerator capacity	Fresh food section only	Helps plan groceries and storage bins
Freezer capacity	Freezer section only	Helps plan frozen food and ice storage

Why it matters

Knowing the cubic feet helps you compare replacement refrigerators, plan kitchen storage, and understand why a side-by-side can feel narrower even when total capacity is high.

Last updated: January 2026

If your Whirlpool WRS325FDAB01 dispenses water but will not make ice, the most common causes are the ice maker being turned off, a kinked water supply line, low water pressure, or the freezer not cold enough. Start with the ice maker ON setting and water supply checks in the WRS325FDAB01 installation guide.

Quick checks that fix most “no ice” issues

• Confirm the ice maker is turned ON (wire shutoff arm down, or switch set to ON depending on your version).
• Make sure the household shutoff valve is fully open.
• Check for a kinked water source line behind the refrigerator; straighten it.
• Verify both doors close completely; some dispenser functions require the freezer door to be fully shut.
• If this is a new hookup or recent filter change, allow time: 24 hours to start making ice and up to 72 hours for full production; discard the first three batches.

Water works, so why can ice still fail?

The dispenser and ice maker can share the same supply but still behave differently. The ice maker fill cycle is sensitive to pressure and flow restrictions.

Symptom	Most likely cause	What to do next
Water dispenses normally, no ice at all	Ice maker turned off or ice bin not seated	Turn ice maker ON; reinstall the bin firmly
Small or hollow cubes	Kinked line or low pressure	Straighten line; confirm shutoff valve fully open
No ice after recent install	Normal startup time	Wait 24 to 72 hours; discard first 3 batches
Ice jams in mold or bin	Jammed ejector area or clumped ice	Clear jam; empty bin and break up clumps

Parts that commonly relate to “no ice”

If the checks above do not restore ice production, these model-matched parts are often involved:

• Refrigerator water inlet valve WPW10179146 (controls water flow to the ice maker fill tube)
• Refrigerator ice maker assembly WPW10300022 (harvests and ejects cubes)

Why it matters

When the ice maker cannot fill correctly or the freezer temperature is not staying cold enough, you can get no ice, small cubes, or repeated jams. Fixing the water supply and ON settings first prevents unnecessary part replacement.

Last updated: January 2026

The “best” side-by-side refrigerator depends on your priorities (reliability, ice and water performance, noise, and fit). If you already own a Whirlpool WRS325FDAB01, the best choice is usually keeping it running efficiently by confirming proper clearances, leveling, and door closing using the WRS325FDAB01 installation guide.

What to look for in the best side-by-side

We recommend comparing models using these practical criteria:

• Fit and clearance: confirm the cabinet opening and door swing space before buying.
• Cooling consistency: stable temps in both compartments with good airflow.
• Ice and water performance: steady ice production and strong dispenser flow.
• Energy use and noise: quieter operation and reasonable electricity usage.
• Serviceability: parts availability (ice maker, inlet valve, control board).

Fit matters first (common deal-breaker)

Side-by-sides are often chosen for narrower kitchens, but door swing and service access still matter. For this Whirlpool platform, typical planning points include:

Planning item	Typical target	Why it matters
Side/top clearance	About 1/2 inch	Helps ventilation and efficiency
Rear clearance	About 2 inches	Room for airflow and water line
Room temperature	60°F to 90°F preferred	Best cooling performance and lower energy use

If you already have WRS325FDAB01: best “upgrade” is maintenance

Before replacing the refrigerator, we focus on the most common performance wins:

• Level the cabinet so doors close easily and seal well.
• Keep airflow paths clear (do not block vents with food packages).
• If ice or water is weak, check the supply line and consider the refrigerator water inlet valve WPW10179146 if diagnostics point to it.
• If ice production is inconsistent, inspect the ice maker and bin fit; the refrigerator ice maker assembly WPW10300022 is the correct assembly listed for this model.

Why it matters

A side-by-side that is properly installed and level typically cools more evenly, wastes less energy, and has fewer ice and water complaints. Fit and door sealing are also major drivers of long-term satisfaction.

Last updated: January 2026

On the Whirlpool WRS325FDAB01 side-by-side refrigerator, the most common issues we see are cooling complaints (too warm, running a lot, or noisy operation) and ice maker or water dispenser problems. Many of these trace back to airflow, temperature control settings, or water supply flow to the ice maker.

Most common symptoms and what they usually point to

• Refrigerator or freezer too warm: doors not sealing, frequent door openings, warm room, or airflow blocked by overpacked shelves.
• Compressor seems to run too much: normal on energy-efficient designs, but also happens with warm room temps or heavy use.
• No ice or small/hollow cubes: water shutoff not fully open, kinked water line, or ice maker switched off.
• Noisy operation: normal sounds from compressor, fans, defrost heater, or water valve cycling.
• Intermittent water dispensing: air in the line after filter changes or supply issues.

Quick checks we recommend first (before replacing parts)

1. Give it time after setup: after a new installation, allow 24 hours for full cooling.
2. Confirm cooling is turned on: verify the controls are set correctly (see the WRS325FDAB01 owner's manual).
3. Check door closure: make sure bins and shelves are seated so doors close completely.
4. Verify water supply for ice: confirm the shutoff valve is fully open and the water line is not kinked.
5. Listen for “normal” noises: buzzing/clicking (water valve), popping (liner expansion), sizzling (defrost), and gurgling (defrost drain) can all be normal.

When a part is commonly involved

If the basic checks do not resolve the issue, these parts are frequently involved in the most common Whirlpool refrigerator complaints:

Problem area	Common symptom	Example part for WRS325FDAB01
Ice production	No ice, small/hollow cubes (after supply checks)	Refrigerator ice maker assembly WPW10300022
Water to ice maker/dispenser	No water flow, slow fill, valve buzzing	Refrigerator water inlet valve WPW10179146
Defrost system	Frost buildup, warming, airflow restriction	Refrigerator defrost bi-metal thermostat WPW10225581

Why it matters

Cooling and ice maker problems often start as small airflow or water-supply issues, but they can lead to food temperature swings, excess frost, and longer run times. Catching the cause early helps protect the compressor and keeps ice and water working reliably.

Last updated: January 2026