Kenmore 11067832794 electric dryer Parts

For Kenmore electric dryer model 11067832794, the model number is printed on the appliance’s model and serial number plate. On this style of dryer, the most reliable place to check first is the door opening area (door frame or inner rim) where the identification plate is commonly mounted; confirm the full number exactly as shown.

Check these spots in order:

• Open the dryer door and look along the door frame or inner lip of the opening
• Look just inside the door opening near the front panel edge
• Check the back panel for a rating/model plate
• If your unit has a console label area, inspect around the control panel ends

For model-specific wording and how Sears expects the information recorded, see the 11067832794 owner's manual.

Write down the model number exactly, including all digits.

We use the exact model number to match the correct Kenmore parts diagrams and compatible replacement parts. Even small differences in a model number can change the correct drum belt, door switch, or thermostat used in the dryer.

• Do not use numbers from the timer knob, cycle chart, or electrical outlet
• Do not guess based on “110 series”; use the full model number from the plate
• If the label is worn, use a flashlight and take a close-up photo to zoom in

Last updated: January 2026

Kenmore dryers, including the Kenmore 11067832794 electric dryer, typically last 10 to 13 years with normal household use. With consistent venting and lint maintenance, it’s common for this model type to reach the upper end of that range.

Use these habits to reduce overheating, wear on the drive system, and long dry times:

• Clean the lint screen before (or after) every load
• Keep the exhaust venting 4-inch heavy metal ducting, not plastic or foil
• Avoid crushing or kinking the vent when pushing the dryer back
• Do not overload; heavy loads strain the drum belt and motor
• Level the dryer to reduce vibration and premature bearing wear
• Periodically clean lint buildup inside the cabinet and at the outside vent hood

For model-specific safety, venting, and care instructions, follow the 11067832794 owner’s manual.

Here’s a practical way to think about service life for an electric dryer like this Kenmore model:

A dryer that’s properly vented and kept clear of lint runs cooler and moves air better; that reduces drying time, lowers stress on the heating circuit, and helps prevent nuisance shutdowns from heat safety devices.

If you’re maintaining or repairing the drive system, these are common wear items on this model:

• Drum belt 341241 (drum rotation)
• Door switch (dryer won’t run if the door circuit is open)
• Thermal fuse/thermal cut-off parts (protect against overheating)

Last updated: January 2026

For Kenmore electric dryer model 11067832794, the most reliable “hard reset” is a power reset: turn the dryer off, unplug it (or switch the breaker off) for 1 to 5 minutes, then restore power and try a normal cycle. For start and restart basics, use the 11067832794 owner’s manual.

• Turn the cycle selector to OFF.
• Unplug the dryer (or turn the 30-amp breaker off).
• Wait 1 to 5 minutes.
• Restore power.
• Close the door firmly.
• Select a timed or normal cycle and press PUSH TO START.

A reset will not bypass a failed safety device or switch. On model 11067832794, common no-start causes include:

• Door not fully closed or a failed door switch
• Overheating condition that opens a safety device (often tied to restricted venting)
• Failed push-to-start switch
• Timer or internal wiring issue

• Door switch WP3406107: confirms the door is closed so the motor circuit can run
• Dryer push-to-start switch WP3395382: starts the motor when pressed
• Cut-off kit 279816: overheating protection components used in the heater/airflow safety circuit (often serviced when overheating is suspected)

A power reset clears temporary control issues, but repeated shutdowns usually point to airflow restriction or a failing start/door circuit component. Correcting the root cause helps prevent overheating and repeat failures.

Last updated: January 2026

For Kenmore electric dryer model 11067832794, we can’t quote a model-specific heating element part price from the information tied to this model because the heating element itself isn’t identified in the provided parts list. In general, electric dryer heating element repairs commonly run $100 to $350 installed, depending on labor and what else is replaced.

Even when the symptom is “no heat,” the failed part is often a heat-protection or temperature-control component. These parts are explicitly listed for this model and can be priced directly.

• Thermal protection: cut-off kit 279816
• One-time safety device: dryer thermal fuse WP3392519
• Temperature control: dryer operating thermostat WP3387134
• Overheat protection: dryer thermostat WP3977767

For safety, venting requirements, and basic checks that help prevent repeat heat failures, use the 11067832794 owner’s manual.

Actual totals vary by region and access time, but these ranges are common for electric dryers like the Kenmore 110 series.

These factors usually change the price more than the brand name.

• Whether the heater circuit failed due to restricted venting
• If multiple heat-safety parts are replaced together
• Condition of wiring terminals (overheated connectors add time)
• How much cabinet disassembly is required
• Service call minimums and local labor rates

If airflow is restricted, a new heater or safety part can fail again. Checking the venting and lint path first helps protect the repair and restores normal drying times.

Last updated: January 2026