Kenmore 11026652503 washer Parts

On Kenmore washer model 11026652503, a bad drain pump usually shows up as water left in the tub, a washer that will not drain or spin, or abnormal pump noise. A steady humming with some gurgling during drain can be normal, so we focus on draining performance and leaks.

Quick symptoms checklist

• Water remains in the washer after the drain portion of the cycle
• Washer will not spin because it cannot drain first
• Loud grinding, rattling, or squealing during drain (not just a steady hum)
• Leaks underneath during fill or drain
• Drain cycle sounds like it is running but water flow is weak or stops
• Repeated “stuck” behavior caused by siphoning or a drain hose issue (not the pump)

Rule out common non-pump causes first

The manual for this washer points to several issues that can mimic a bad pump. Use this order because it is faster and avoids unnecessary parts.

• Lid is open: this model will not agitate or spin with the lid open
• Drain hose height or blockage: the drain hose can be clogged, or the end of the hose can be too high (over about 96 inches)
• Siphoning/air gap problem: the drain hose should fit securely but not be sealed; it needs an air gap
• Excessive sudsing: too much detergent can prevent proper draining

What you see	Most likely cause	What to check next
Hums, drains slowly	Partial clog in pump or hose	Inspect hose path, then check pump inlet
Hums, does not drain	Jammed impeller or failed pump	Check for blockage, then replace pump
Drains but leaks	Cracked pump housing or loose clamps	Look for drip source under washer

How we confirm the pump is the problem

1. Unplug the washer.
2. Check the drain hose for kinks, clogs, and correct standpipe setup (air gap).
3. If the hose is clear, inspect the pump area for debris (coins, socks, lint) and signs of leaking.
4. If the pump is noisy, leaking, or the impeller is damaged or jammed, replace the pump.

If replacement is needed for this model, use the washer drain pump WP3363394. For setup details like securing the drain hose and preventing siphoning, follow the installation guide.

Why it matters

A weak or failed drain pump can leave water in the tub, prevent spinning, and cause leaks that can damage flooring. Catching it early also helps you avoid strain on the drive system.

Last updated: February 2026

Yes. Kenmore Elite is Kenmore’s higher-end line; it typically adds upgraded performance, quieter operation, and more premium features than standard Kenmore models. For your Kenmore washer model 11026652503, the exact feature set is listed in the 11026652503 owner's manual.

How Kenmore Elite compares to other Kenmore lines

In general, Kenmore’s lineup breaks down like this:

Line	Typical position	What you usually get
Kenmore	Core line	Solid basics, fewer premium options
Kenmore Elite	High end	More cycles/options, better capacity or performance features, upgraded fit and finish
Kenmore PRO	Pro-style	Pro-focused styling and features (varies by product type)

What “high end” means for a washer

For washers, “high end” usually shows up as a combination of features and build choices that improve cleaning results and convenience, such as:

• More wash cycles and temperature options for different fabrics
• Better vibration control and smoother spinning
• Improved soil removal and rinse performance
• More durable drive and suspension components
• More convenience features (cycle customization, dispensers, etc.)

Why it matters

Knowing whether a washer is “high end” helps set expectations for maintenance and repair decisions. Premium models often use more specialized components; when performance drops (no spin, no drain, poor agitation), replacing the correct part for the exact model matters.

If you’re troubleshooting performance issues on model 11026652503, common wear items we often see include the agitator dog 80040 and the washer lid switch assembly WP8318084. You can order replacement parts from the parts list for this model, or search by model number on Sears PartsDirect.

Last updated: February 2026

To hard reset your Kenmore washer model 11026652503, we recommend a simple power reset first: unplug the washer (or switch off the breaker) for 1 minute, then restore power and try a normal cycle. For this model style, that reset clears many “stuck” control states without changing any mechanical settings; see the 11026652503 owner's manual.

Quick reset options (start here)

• Power reset: Unplug for 1 minute, then plug back in.
• Control stop/restart (timer models): Push in the cycle control knob to stop; pull it out to restart.
• Lid reset (if the cycle will not resume): Close the lid fully, wait 5 seconds, then try starting again.
• Drain-first check: If the tub is full of water, set to a drain/spin and listen for the pump.

If the washer will not drain or spin after a reset

A “reset” will not fix a drain restriction or failed drain component. If you hear humming but water stays in the tub, check the drain hose for kinks and confirm the household drain can handle fast flow. If the hose and drain are clear, the drain pump is the most common next suspect.

• Inspect the drain hose routing and height per the 11026652503 installation guide.
• Check for clogs at the pump inlet and in the tub-to-pump hose.
• If the pump is noisy, seized, or leaking, replace the washer drain pump WP3363394.

What a reset does (and does not do)

Action	What it helps	What it will not fix
Unplug 1 minute	Clears minor control glitches, restarts the cycle logic	Broken lid switch, bad pump, worn drive parts
Stop/restart with knob	Pauses and resumes a cycle safely	Drain clogs, leaks, out-of-level vibration

Why it matters

Resetting is a fast way to rule out a temporary control issue before replacing parts. If symptoms return immediately (no drain, no spin, no agitation), that points to a component problem such as the lid switch, drain pump, or drive system.

If you need parts for model 11026652503, you can order from the parts list for this washer or search by model on Sears PartsDirect.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years. For your Kenmore 11026652503 top-load washer, consistent care (proper installation, correct loading, and routine cleaning) is what most directly determines whether it reaches the high end of that range; see the 11026652503 owner's manual for model-specific care steps.

Typical lifespan and what changes it

Most washers land in the same general window, but these factors move the needle the most:

• Load size and frequency: daily heavy loads shorten life faster than moderate weekly use
• Leveling and flooring: an unlevel washer increases vibration and wear on the drive system
• Water quality and detergent use: excess detergent can leave residue that stresses moving parts
• Cold-weather storage: operating or storing at or below 32°F (0°C) can cause damage if water remains inside
• Timely repairs: replacing small wear parts early can prevent bigger failures

Quick care checklist (best ROI)

These habits help a Kenmore top-load washer like model 11026652503 last longer:

• Keep the washer level and on a firm floor
• Avoid overloading; distribute items evenly around the basket
• Use the right amount of detergent (too much causes buildup)
• Periodically run a cleaning cycle (or a hot wash with no laundry, if your cycle options allow)
• In freezing conditions, winterize the washer so trapped water does not damage components

Common “wear points” as the washer ages

If performance drops, these are frequent repair areas on many Kenmore top-load designs:

Symptom	Common cause	Example part for 11026652503
Won’t drain or leaves water in tub	Drain pump issue or blockage	Washer drain pump WP3363394
Won’t spin or agitates poorly	Lid switch not sensing closed lid	Washer lid switch assembly WP8318084
Agitator moves but clothes don’t circulate well	Worn agitator dogs	Agitator dog 80040

Why it matters

Knowing the 10 to 15 year lifespan helps you decide when a repair (like a drain pump or lid switch) is a smart investment versus when multiple major drive-train issues may signal end-of-life.

You can order replacement parts for Kenmore 11026652503 from the parts list for this model, or search by model number on Sears PartsDirect.

Last updated: February 2026