Kenmore 11023102311 washer Parts

Kenmore washer model 11023102311 is a top-load design; washers in this Kenmore 110 platform are typically about 3.2 to 3.6 cu. ft. capacity. For the exact published capacity for your specific unit, we recommend confirming it in the 11023102311 owner's manual.

How to confirm the exact capacity

Capacity is usually listed in the specifications section of the manual or on the model rating label.

• Check the Specifications section in the 11023102311 owner's manual
• Look for a model and serial tag on the washer cabinet (often under the lid or along the rim)
• If the manual lists dimensions but not capacity, use the model tag details to match the correct spec sheet
• Avoid relying on “series” estimates when comparing to a new washer; capacity can vary within the 110 family

Typical capacity range (what most owners can expect)

Here is a practical range we use for Kenmore 110 top-load washers of this style:

Washer type	Typical capacity range	Best for
Standard top-load (agitator)	3.0 to 3.6 cu. ft.	Everyday mixed loads
Larger top-load (some variants)	3.8 to 4.3+ cu. ft.	Bulky items, fewer loads

Why it matters

Capacity affects how much you can load without poor cleaning, out-of-balance spinning, or extra wear on drive components like the belt and gearcase. If you routinely overload, it can also contribute to vibration and suspension issues.

Last updated: February 2026

Your Kenmore washer model number is printed on the appliance ID label; on Kenmore model 11023102311, it’s typically under the lid (top-load) or around the cabinet opening and it will match the format 110.XXXXXXXX. Use that exact number to choose compatible parts and troubleshooting info in the 11023102311 owner's manual.

Where to look on the washer

Check these common label locations first:

• Under the lid: along the rim of the tub opening or underside of the lid
• Rear of the cabinet: near the power cord entry or back panel
• Side of the cabinet: near the control console area
• Inside the cabinet opening: around the top frame (varies by revision)

What the model number looks like (and what to write down)

For Kenmore washers, the model number is usually a long numeric string and often starts with 110.

What to capture	Example for this washer	Why it matters
Model number	11023102311	Matches parts diagrams and fitment
Serial number	(from same label)	Helps with production date and service history
Type	Top-load washer	Guides troubleshooting steps

Tips to avoid ordering the wrong part

When you’re matching parts for Kenmore 11023102311, we recommend:

• Copy the model number exactly (all digits, no spaces)
• Take a clear photo of the label before it wears or fades
• Match the symptom to the correct system (lid lock, drive, drain, fill)
• Use the manual’s component names so you search the right term
• If the washer won’t start or won’t spin, confirm the lid is locking; a common related part is the washer lid lock assembly W10404050

Why it matters

Kenmore model numbers identify the exact design family and revision; even small differences can change which drive belt, lid lock, or control board fits. Using the correct model number prevents returns and speeds up repair.

Last updated: February 2026

To unclog the drain hose on your Kenmore washer model 11023102311, we unplug the washer, verify the drain hose is installed correctly (standpipe depth and hose height), then clear debris from the hose and the household standpipe. Confirm the fix by running a Drain/Spin or Rinse/Spin test from the 11023102311 owner's manual.

Safety first

• Unplug the washer or switch off the breaker.
• Turn off both water faucets.
• Keep towels and a shallow pan ready for water in the hose.
• Do not use sharp tools that can puncture the hose.

Step-by-step: clear the clog

1. Pull the drain hose out of the standpipe or laundry tub.
2. Check for kinks, crushing, or a pinched section behind the washer.
3. Verify installation basics from the 11023102311 installation guide:
   • About 4.5 in. (113 mm) of hose should be inside the standpipe.
   • Do not force excess hose into the standpipe or lay it on the bottom of the tub.
   • Use the drain hose form when required.
4. Flush the hose with hot water; for heavy buildup, soak the end in hot water and vinegar, then flush again.
5. Clear the household drain/standpipe; a restricted standpipe can mimic a washer hose clog.
6. Reinstall and secure the hose; do not tape over the drain opening.

If it still will not drain

Symptom	Likely cause	Next step
Drains slowly, clothes still wet	Partial clog or excess suds	Flush hose; run Rinse/Spin with no detergent
Water backs up at standpipe	House drain restriction	Clear standpipe or contact a plumber
Stops draining during cycle	Hose pushed too far in or hose too high	Correct standpipe depth; keep hose end under 96 in. high

Why it matters

A restricted drain hose or standpipe prevents normal pump-out, leaving loads wet and increasing strain on the drain system. Correct hose depth, height, and a clear standpipe help prevent repeat clogs.

Last updated: February 2026

Kenmore 11023102311 is a Kenmore brand top-load washer model. For model-specific identification details (including the model series shown in the documentation), we recommend checking the 11023102311 owner's manual.

How to confirm you have the right model

We use the model number to match the correct Kenmore parts, diagrams, and repair instructions.

• Look for the model/serial tag under the lid or around the tub opening
• Match the full model number exactly: 11023102311
• Use the manual to confirm the model series and feature set
• When ordering parts, match both the symptom and the part description

Common parts people order for this Kenmore washer

If you are identifying the washer so you can repair it, these are common wear items for Kenmore top-load models like 11023102311:

• Washer lid lock assembly W10404050 (lid must lock for the washer to start)
• Drive components such as the cam and belt (for agitation/spin issues)
• Suspension/damper parts (for out-of-balance or shaking)

Quick part-to-symptom guide

Symptom	Often related to	Example part for this model
Won’t start, lid won’t lock	Lid lock system	Washer lid lock assembly
Won’t agitate or spin	Drive system	Cam, washer drive belt
Excessive vibration	Suspension	Washer damper

Why it matters

Kenmore uses multiple design platforms across different series; using the exact model number 11023102311 ensures we point you to the correct Kenmore washer parts (like the lid lock, drive belt, or gear case) and the right repair steps.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years with normal household use. For Kenmore model 11023102311, routine care (correct detergent amounts, occasional warm or hot washes, and periodic inspections) helps you reach the upper end of that range; neglected maintenance shortens it.

What most affects washer lifespan

• Overloading the basket (extra strain on the drive system and suspension)
• Too much detergent (residue buildup that can cause odors and performance issues)
• All-cold washing only (can contribute to residue over time)
• Worn hoses or leaks (water damage risk and downtime)
• Out-of-level installation (more vibration, faster wear on dampers and drivetrain)

Maintenance schedule we recommend (based on common washer care)

The Use & Care Guide for this style of Kenmore washer calls out several key habits; use the 11023102311 use & care manual for the full maintenance section.

Task	How often	Why it matters
Inspect inlet hoses for bulges, kinks, cuts, wear, leaks	Periodically	Prevents sudden hose failure and water leaks
Replace water inlet hoses	Every 5 years	Reduces risk of hose rupture
Use correct detergent amount	Every load	Helps prevent residue and odor buildup
Run some warm or hot washes	Occasionally	Helps dissolve and flush residues

Parts that commonly wear as a washer ages

Wear items are normal over time; replacing them can extend service life and improve performance.

• Drive belt (slipping, squealing, weak spin): washer drive belt WPW10006384
• Suspension/dampers (banging, walking, out-of-balance): washer damper W10780045
• Lid lock (won’t start, lid won’t lock/unlock correctly): washer lid lock assembly W10404050
• Water inlet valve (slow fill, no fill, hot or cold not working): washer water inlet valve assembly WPW10683603

Why it matters

A washer that is kept clean, level, and not overloaded runs with less vibration and less strain on the gear case, belt, and tub support. That directly reduces breakdowns and helps your Kenmore 11023102311 reach its normal 10 to 15 year lifespan.

Last updated: February 2026