Kenmore Elite 72187583611 microwave/hood combo Parts

The Kenmore Elite microwave/hood combo model 72187583611 measures 29 7/8 in. wide x 17 13/16 in. high x 15 13/16 in. deep (outer dimensions). These are the cabinet dimensions you need for fit, clearance, and replacement planning; confirm your installation clearances in the 72187583611 installation guide.

Dimensions at a glance

Measurement	Size (inches)
Width	29 7/8
Height	17 13/16
Depth	15 13/16

How we recommend measuring for fit

• Measure the opening width between cabinets at the mounting height.
• Measure height from the bottom mounting surface to any cabinet trim or shelf.
• Measure depth from the wall to the front edge of the cabinet line (include door clearance).
• Verify the required space above the cooktop and any slide-out hood clearance.
• If replacing an older unit, compare the old unit’s outer dimensions to the specs in the 72187583611 owner’s manual.

Why it matters

Correct outer dimensions help prevent common install problems like cabinet interference, blocked venting, and a door that cannot open fully. For over-the-range models, clearances also affect how well the vent hood captures smoke and heat.

Related spec you may want to confirm

Spec	What it affects
Electrical requirements (120V/60Hz, dedicated circuit recommended)	Prevents nuisance tripping and power issues
Net weight (61 lb.)	Mounting support and safe handling

Last updated: February 2026

To reset your Kenmore Elite microwave model 72187583611, we recommend doing a basic power reset first (unplug or switch off the breaker briefly, then restore power). This clears many control glitches without changing your saved settings; for model-specific control steps, use the 72187583611 owner's manual.

Quick reset options (start here)

• Power reset: Unplug the microwave or turn off the circuit breaker.
• Wait 60 seconds to let the control board fully discharge.
• Restore power and set the clock if prompted.
• Test a simple cook cycle (for example, 1 minute with a cup of water).
• If the display is blank, press Energy Saving to turn the display back on.

If the display is off (not a failure)

This model has an Energy Saving feature that can turn the display off after idle time.

• Touch Energy Saving once to turn the display off.
• Touch Energy Saving again to turn the display on.

What you will see

Situation	What it means	What to do
Display goes dark after a few minutes	Energy saving mode	Press Energy Saving
Display is on but keys act odd	Control glitch	Do the power reset
Unit runs but does not heat	Heating circuit issue	See why is my microwave not heating

When a “reset” points to a repair

If the microwave repeatedly loses power, blows a fuse, or stops when you close the door, a reset will not fix the root cause. These issues commonly involve the door interlock system or internal protection devices.

• If it goes dead and then comes back, check the door closes firmly and latches cleanly.
• If it goes dead and stays dead, a blown fuse is common.
• If it stops when the door moves, an interlock switch or latch housing can be involved.

Helpful repair reading: how to replace a microwave fuse.

Why it matters

A proper reset helps separate a simple control-board lockup from a real electrical or heating problem. That saves time and helps you choose the right next step, whether it is a settings change, a fuse check, or service.

Last updated: February 2026

A Kenmore Elite microwave/hood combo like model 72187583611 typically lasts 9 to 10 years with normal household use and basic care (keeping vents and filters clean, avoiding slamming the door, and not running it empty). For care and cleaning specifics, use the owner's manual.

What affects lifespan the most

• Ventilation and heat: Grease buildup restricts airflow and raises internal temperatures.
• Door use: Worn latches or switches from hard closing can stop heating or prevent starting.
• Electrical stress: Power surges and repeated fuse blows shorten control and high-voltage component life.
• Cleaning habits: Spills and steam damage the keypad and display over time.
• Usage pattern: Long cook times and frequent reheating cycles add wear.

Maintenance that helps you reach (or beat) the average

• Wash the grease filter regularly; replace it when it no longer cleans well (see microwave grease filter 5230W1A012G).
• Replace the charcoal filter on recirculating setups as recommended for odor control (see lg microwave charcoal filter 5230W1A003A).
• Keep the vent grille and intake areas clear of dust and grease.
• Use microwave-safe cookware and never run the unit empty.
• If the unit repeatedly blows a fuse, stop using it and correct the underlying cause before replacing parts.

Quick guide: repair vs replace

Symptom	Common wear area	Typical next step
Runs but does not heat	High-voltage system	Diagnose by a qualified technician; parts may include magnetron, diode, capacitor
Dead display, no response	Power supply or control	Check house power, then inspect fuse and control circuit
Starts only with door held	Door interlock system	Inspect latch and interlock switches

Why it matters

Knowing the 9 to 10 year average helps you decide whether to invest in repairs (like a door interlock switch or filter maintenance) or plan for replacement, especially if multiple major components are failing.

Last updated: March 2026