Kenmore Elite 79080373310 microwave/hood combo Parts

For Kenmore Elite microwave/hood combo model 79080373310, the overall exterior size is typically about 30 inches wide, 16 to 17 inches high, and 15 to 17 inches deep. For the exact cabinet cutout and mounting clearances, use the measurements listed in the 79080373310 installation guide.

What measurements matter (and where they’re used)

When you’re checking fit over a range or inside a cabinet run, we focus on these dimensions:

• Overall width: determines if it fits the space and aligns with the range below
• Overall height: affects cabinet clearance and mounting plate position
• Overall depth: affects how far it projects past the cabinets and backsplash
• Mounting and venting clearances: determines safe installation and proper airflow
• Stud spacing and wall support: determines where the bracket and bolts can go

Quick size guide for this style of microwave

Most over-the-range microwaves in the Kenmore Elite class fall into a narrow size range.

Measurement	Typical range (inches)	Why it matters
Width	29 7/8 to 30	Matches standard 30-inch ranges
Height	16 to 17	Cabinet clearance and mounting
Depth	15 to 17	Door swing, backsplash clearance

How to confirm the exact size before you buy or install

Use this checklist to avoid a fit problem:

• Compare your opening to the dimension diagram in the 79080373310 installation guide
• Measure your existing unit width, height, and depth with the door closed
• Confirm you can fasten the microwave to at least one wall stud (a key installation requirement)
• Verify your cabinet bottom style (flat, framed, recessed) because it changes wall plate placement
• If you are reusing an old bracket, match the bracket and hole pattern to the guide, not just the width

Why it matters

Even a 1/4-inch difference can prevent the mounting plate from lining up with studs or cabinet holes. Using the model-specific installation measurements helps ensure safe support, correct venting, and a clean fit over a 30-inch range.

Last updated: February 2026

For the Kenmore Elite microwave/hood combo model 79080373310, the microwave cooking output is 1050 watts. That is the wattage that matters for heating performance and cook times; the unit’s electrical power draw is higher than the cooking output.

Where to find the wattage for model 79080373310

We list the key specs in the 79080373310 owner's manual, including the microwave output power and the electrical rating.

• Microwave output power: 1050W (cooking performance)
• AC power required: 1650W (power the unit consumes)
• Electrical circuit: 120VAC, 60 Hz; typically on a dedicated 15 to 20 amp branch circuit
• Why two numbers: output watts heat food; input watts run the magnetron, fan, controls, and losses

Quick spec comparison (output vs input)

Spec type	What it means	Value for 79080373310
Output power	Heating/cooking strength	1050W
Input power required	Electrical draw from the outlet	1650W

Why it matters

When recipes say “cook times based on a 1000W microwave,” your Kenmore Elite 79080373310 is slightly higher at 1050W, so cook times are usually a bit shorter. If your home voltage is low, heating can still feel slower even with the correct wattage.

If your microwave seems weak even though it is 1050W

Use these checks before replacing parts:

• Confirm you are using High (100%) power level for testing.
• Heat 1 cup of water in a microwave-safe cup; compare time-to-boil to typical expectations.
• Make sure the door closes firmly; a worn latch or switch can cause odd operation.
• If the unit runs but does not heat, follow a diagnostic path like why is my microwave not heating.

Last updated: February 2026

For your Kenmore Elite microwave/hood combo, the model number is printed on the appliance ID label. On model 79080373310, you will typically find that label when you open the door, either on the door frame, along the side of the control panel, or on the interior side wall. See the 79080373310 use and care guide for label location and identification details.

Where to look on an over-the-range Kenmore microwave

Check these common label locations (start with the door area first):

• Door frame (around the opening when the door is open)
• Along the side of the control panel (visible with the door open)
• Interior side wall of the microwave cavity
• Back panel (requires pulling the unit forward, if accessible)
• Behind the vent grille area (some installations)

What the model number looks like (and why it matters)

Kenmore model numbers are usually a series of digits; for this unit, the full model is 79080373310. Using the exact model number helps us match the correct Kenmore parts list, wiring diagram references, and service procedures.

Quick ID checklist

• Write down the full model number exactly as shown
• Also record the serial number (helpful for service and production variations)
• Take a clear photo of the label before it wears or fades

If you cannot see the label easily

If the microwave is mounted over the range and the label is hard to access, use the installation steps and diagrams to understand safe access points and mounting clearances in the installation guide.

Situation	Best next step
Label is greasy or faded	Clean gently with mild soap and water; avoid abrasives
Door area has no label	Check interior side wall, then back panel
Unit is tightly installed	Use the mounting guidance in the installation guide before moving it

Why it matters

The correct model number ensures you get compatible parts (like a door switch, latch hook, or control board) and avoids ordering a similar-looking part that will not fit or wire correctly.

Last updated: February 2026

To reset your Kenmore Elite microwave/hood combo model 79080373310, we recommend doing a basic power reset first: unplug the microwave (or turn off the breaker) for about 1 minute, then restore power and set the clock using the 79080373310 owner's manual.

Quick reset options (from easiest to most involved)

• Power reset: Unplug for 60 seconds, then plug back in.
• Breaker reset: Turn the dedicated microwave circuit breaker OFF, wait 60 seconds, then turn it ON.
• Clear a cooking program: Press STOP to cancel cooking and clear the display.
• Reset after a power interruption: Restore power, then set the time of day using Clock & Settings.
• If the display is blank after reset: Check the outlet and house fuse/breaker, then try the reset again.

What “STOP” actually resets

On the 79080373310, the STOP pad is designed to erase an incorrect command, cancel a program during cooking, or clear the display. That is the correct “reset” for most day-to-day issues like a wrong time entry or a stuck cook cycle.

Reset type	What it fixes	What it does not fix
STOP key reset	Wrong entry, cancel cooking, clear display	No power, dead display, heating problems
Power reset (unplug/breaker)	Glitches, frozen keypad, odd display behavior	Failed door switch, control board, heating circuit

Why it matters

A proper reset helps you separate a simple control glitch from a real failure. If the microwave powers on but acts erratically, a power reset often restores normal operation without replacing parts.

If it still will not run after resetting

If the unit has power but will not start, the door interlock system is a common cause. On this model, that can involve the door switches and latch components such as the microwave door switch 5304509459 or latch hook 5304509457.

Last updated: February 2026