Kenmore 10658153800 side-by-side refrigerator Parts

Kenmore Elite refrigerator height varies by model. For the Kenmore side-by-side refrigerator model 10658153800, the exact overall height is listed in the specifications section of the 10658153800 owner's manual; use that measurement to confirm fit under cabinets and through doorways before moving the unit.

How to find the correct height for your exact model

We recommend using the model-specific specs because “Kenmore Elite” covers many sizes.

• Check the specifications/dimensions section in the 10658153800 owner's manual
• Measure your refrigerator at home to confirm (floors can be uneven)
• Measure height to top of case and height to top of hinge (hinges often sit higher)
• Include clearance for ventilation and door swing
• If you plan to remove doors for moving, measure the cabinet opening and path separately

Clearances that affect real-world fit

Even if the refrigerator height fits, you still need installation clearance for airflow and usability.

• Allow about 1/2 inch space on each side and at the top for ventilation
• If installed next to a fixed wall, allow about 2 inches minimum on the hinge side so the door can swing open
• If the unit has an ice maker, allow extra space behind for the water line connection

Quick measurement checklist

What to measure	Why it matters
Height to top of case	Confirms cabinet and soffit clearance
Height to top of hinge	Prevents surprises when sliding into place
Opening height (floor to cabinet)	Ensures the unit can be tilted/rolled in
Leveling leg adjustment range	Leveling can slightly change final height

Why it matters

A refrigerator that is even slightly too tall can bind under cabinets, restrict airflow, and make leveling difficult. Confirming the model-specific height for 10658153800 helps avoid damage during installation and ensures proper cooling performance.

Last updated: February 2026

On Kenmore model 10658153800, a bad compressor usually shows up as poor cooling with the unit running a lot, repeated clicking as it tries to start, or unusual compressor sounds. Because this refrigerator uses a high-efficiency compressor that can run longer normally, we confirm compressor failure by ruling out airflow, power, and control issues first (see the 10658153800 owner's manual).

Quick checks before blaming the compressor

Many “bad compressor” symptoms are caused by normal operation or a different failed part.

• Verify the outlet has power; test it with a lamp
• Make sure the temperature controls are turned on and set correctly
• If it was just installed or restarted, allow 24 hours to cool completely
• Listen for normal sounds (buzzing at the ice maker fill, pulsating from compressor/fans)
• Check that doors close fully and seals are making contact
• Make sure airflow is not blocked inside the freezer and fresh food sections

Symptoms that strongly point to a compressor problem

These signs are more consistent with a compressor that is failing to start or run efficiently:

• Clicking every few minutes (start attempt, then shutoff)
• Compressor is very hot to the touch after repeated start attempts
• Refrigerator runs constantly but temperatures stay unsafe (fresh food above 40°F)
• You do not hear the typical steady running or gentle pulsating sound you used to hear

Normal vs. not normal (sound and run time)

What you notice	Often normal on this model type	More likely a problem
Long run times	High-efficiency compressor may run longer	Runs nonstop and never reaches set temps
Pulsating/high-pitched sound	Compressor/fans adjusting performance	Loud clicking with no cooling
Buzzing	Water valve filling ice maker	Buzzing plus no ice/water flow issues elsewhere

What to check that can mimic a bad compressor

If these items fail, the compressor may be fine but the refrigerator still will not cool.

• Frost buildup restricting airflow (defrost system issue); consider the refrigerator defrost bi-metal thermostat WPW10225581
• Evaporator fan not moving air; the fan motor is a common suspect
• Dirty or blocked condenser area reducing heat removal
• Temperature control or electronic control not calling for cooling
• Start components (relay/capacitor) failing; some models use a run capacitor such as refrigerator run capacitor WPW10662129

Why it matters

Replacing a compressor is one of the highest-cost refrigerator repairs. Doing the quick power, control, and airflow checks first helps avoid replacing the wrong part and gets you back to stable temperatures faster.

Last updated: February 2026

A Kenmore side-by-side refrigerator model 10658153800 usually stops cooling because power is interrupted, the temperature controls are off or mis-set, airflow is blocked, or a cooling-system component (fan, defrost system, compressor start parts) is failing. Use the checks below to pinpoint the cause quickly; see the owner's manual for control and operating details.

Quick checks first (no tools)

• Confirm the outlet has power (plug in a lamp) and reset the breaker if needed.
• Make sure the refrigerator controls are ON and not set too warm.
• Allow 24 hours after a new install or a long power outage for full cool-down.
• Check that doors close fully and nothing is holding them open.
• Make sure vents inside both compartments are not blocked by food packages.

Cooling airflow problems (common)

If the unit has power but temperatures rise, airflow is often the issue.

• Listen for the evaporator fan; it circulates air through the refrigerator and freezer.
• Heavy frost on the freezer back panel points to a defrost problem.
• A noisy, weak, or non-spinning fan can reduce cooling.

Helpful part to consider if the fan is damaged: Refrigerator evaporator fan motor WP2315549.

Water and ice related issues that can look like “not cooling”

Sometimes the complaint starts after ice or water problems, especially if doors are left ajar during troubleshooting.

• If the ice maker is cycling, you may hear buzzing when the water valve fills it.
• If the freezer door is not fully closed, cooling performance drops fast.
• If you are also seeing slow water flow, replace the filter and recheck temps.

Common maintenance part: Genuine Kenmore refrigerator water filter EDR3RXD1. For step-by-step filter help, use how to replace the water filter in a Kenmore refrigerator.

What the symptoms usually mean

Symptom	Most likely area to check	What to do next
No lights, no sound	Power supply	Verify outlet, breaker, cord
Runs a lot but warm	Airflow or defrost	Check vents, frost buildup, fan
Freezer cold, fridge warm	Airflow/damper area	Clear vents, check evaporator fan
Clicking, won’t start	Start components	Consider professional diagnosis

Why it matters

When cooling stops, food temperatures can rise quickly. Fast checks like power, controls, door closure, and vent blockage prevent unnecessary part replacement and help you decide whether you are dealing with a simple airflow issue or a deeper defrost/compressor problem.

Last updated: February 2026

On Kenmore side-by-side refrigerator model 10658153800, the model number is printed on the appliance identification label inside the fresh food (refrigerator) compartment, typically on a side wall near the top or around the crisper area. Use the exact model number when ordering parts or checking specifications in the owner's manual.

Where to look first

Check these common label locations on a Kenmore side-by-side refrigerator:

• Inside the refrigerator section on the left or right interior wall
• Near the ceiling of the fresh food compartment (behind or beside the top shelf)
• Around the crisper pan area (side wall or just above the crispers)
• On the frame edge behind the refrigerator door (visible when the door is open)
• Occasionally behind the base grille area (less common for the model label)

What the label shows (and why it matters)

The same label usually includes both the model number and serial number. The model number identifies the exact design family so we can match the correct Kenmore parts such as shelves, door bins, and water filtration components.

Item on label	What it’s used for	When you need it
Model number (10658153800)	Matches parts and diagrams	Ordering parts, checking fitment
Serial number	Identifies production run	Service history, age reference

Tips for reading and using the model number

• Copy the model number exactly as printed (all digits matter).
• Take a clear photo of the label before you start a repair.
• Use the model number when selecting common replacement items like the genuine Kenmore refrigerator water filter EDR3RXD1 or storage parts.

Why it matters

Kenmore side-by-side refrigerators can look similar across multiple model series, but small differences affect fit and function (door bins, shelves, ice maker parts, and controls). Using 10658153800 prevents ordering the wrong part and saves time during troubleshooting.

Last updated: February 2026