Installation guide
Owner’s manual
Error Codes
How to hard reset a Kenmore dryer?
To hard reset your Kenmore gas dryer model 11073952101, unplug it (or switch the breaker off) for about 1 minute, then restore power and start a new cycle. This clears many temporary control and cycle issues; if the dryer still will not run, follow the basic “won’t start” checks in the 11073952101 owner’s manual.
- Turn the cycle selector to OFF.
- Unplug the dryer (or turn both dryer breakers off if it is hardwired).
- Wait 60 seconds.
- Restore power.
- Close the door firmly.
- Select a cycle and press PUSH TO START.
These checks match the most common “no run” causes for this model:
- Confirm the dryer is plugged into a grounded 3-prong outlet.
- Check house power; many dryers use 2 fuses or 2 breakers, and both must be on.
- Make sure the door is fully closed; a failed door switch can prevent starting.
- If the drum light comes on but the dryer will not run, test the dryer door switch WP3406107.
- If the dryer ran previously and then stopped and now will not restart, check the dryer thermal fuse WP3390719 (a blown fuse often points to restricted venting).
| Symptom | Most likely area | What we do next |
|---|---|---|
| No lights, no response | Power supply | Reset breakers, verify outlet power |
| Lights on, won’t start | Door switch, timer/control | Confirm door latch, test door switch |
| Starts then stops, won’t restart | Overheat protection | Check venting, test thermal fuse |
A hard reset clears a stuck cycle state, but it does not fix an underlying failure. If a safety device like a thermal fuse opens, the dryer will not run again until the airflow restriction is corrected and the failed part is replaced.
Last updated: February 2026
What is an F1 code on a Kenmore dryer?
On Kenmore dryers like model 11073952101, an F1 code indicates the dryer is detecting a problem in the electronic control system (the control board, keypad/user interface, or the wiring between them). Start with a power reset and connection checks before replacing parts.
- Unplug the dryer or switch off the breaker for 5 minutes, then restore power and try a timed cycle.
- If the code returns, unplug again and let the control sit powered off for 10 minutes.
- Confirm the dryer is plugged into a grounded 3-prong outlet and not using an extension cord; see the 11073952101 installation guide.
- Check the console area for moisture, stuck buttons, or a jammed selector.
- If the dryer was recently moved, verify it sits level and the cord is firmly seated.
| What triggers F1 | What you may notice | What to do next |
|---|---|---|
| Keypad/button input problem | Beeping, code after pressing Start | Inspect for stuck keys; dry the console |
| Loose wiring at the control | Code comes and goes, random stopping | Reseat harness connections at the control |
| Control board fault | F1 returns immediately after reset | Replace the failed control component |
If the dryer also shuts off mid-cycle or has no heat, fix airflow and safety cutoffs because overheating and power interruptions can cause control errors.
- Clean the lint screen and confirm strong airflow at the exhaust outlet
- Inspect the vent for crushing, long runs, or lint blockage
- If the dryer will not run, test the dryer thermal fuse WP3390719
The dryer uses the control system to manage motor operation, heat, and cycle timing. When it flags F1, the dryer cannot reliably run the cycle, so addressing power, wiring, and control inputs prevents repeat shutdowns.
For operating and troubleshooting steps specific to your dryer, use the 11073952101 owner’s manual.
Last updated: February 2026
What model number is the Kenmore 11073952101 dryer?
The model number for this Kenmore gas dryer is 11073952101. You’ll find the complete model number and serial number on the model and serial label located at the top inside the dryer door well; our 11073952101 owner's manual shows where to record it for future service.
Check these common label locations for Kenmore dryers, starting with the most likely spot for model 11073952101:
- Open the dryer door and look at the top inside the door opening (door well)
- Wipe dust off the label so all digits are readable
- Write down the full model number exactly as shown (all digits)
- Record the serial number too; it helps match the correct parts list
- Keep the information with your purchase records for service and maintenance
We use the model number to match the correct Kenmore parts and diagrams for your exact gas dryer configuration. Even small model-number differences can change the correct drum support, belt routing, or gas burner components.
| What you’re doing | Why the exact model number matters | Example outcome |
|---|---|---|
| Ordering replacement parts | Ensures correct fit and wiring/connector style | Correct door switch, timer, or thermal fuse |
| Troubleshooting symptoms | Points you to the right procedures and specs | Faster diagnosis of “won’t start” or “no heat” |
| Using installation requirements | Confirms venting and gas connection guidance | Safer setup and better drying performance |
If you see a different Kenmore model number (for example, a 110.######## format), treat it as a different machine unless it matches 11073952101 exactly. For installation and identification details specific to your dryer, use the 11073952101 installation guide.
Using the exact model number prevents ordering the wrong Kenmore dryer parts and helps avoid repeat repairs, especially on gas dryer components like the igniter, valve coils, and thermostats.
Last updated: February 2026
