Snapper 355ZB2654 (5900748) lawn mower Parts

For a Snapper riding mower, your model number is printed on the mower’s identification label; for this parts page, the model is Snapper 355ZB2654 (series 355Z, code 5900748). Use the label’s model number to match the correct parts list and the correct owner's manual.

On most Snapper riders and zero-turn mowers, the ID label is on the frame in an easy-to-see spot. Check these common locations first:

• Rear of the mower frame (often near a lower corner)
• Under or just below the floor pan
• Under the seat or on the seat pan support
• Near the engine compartment or rear fender area
• On the mower deck shell (less common for the primary model tag)

We recommend recording all ID fields from the tag so you can get the right diagrams, parts, and service procedures.

• Mower model number (example for this page: 355ZB2654)
• Serial number (helps confirm production run)
• Engine model/type/code (important for engine-specific tune-up parts)
• Date purchased (useful for maintenance tracking)

Snapper model families can look similar, but small differences (deck setup, drive components, electrical harness routing) change which parts fit. Confirming the model number first prevents ordering the wrong items, especially for drivetrain and chassis parts.

Once you confirm the model number, compare it to the parts list for 355ZB2654. Common chassis and running-gear items on this model include the Snapper wheel 1714760SM and Snapper bearing 2108202SM.

Last updated: February 2026

For your Snapper 355ZB2654 mower, the most reliable way to determine the year is to use the model and serial number information from the ID tag on the machine, then confirm the production details using the identification section in the owner's manual.

On most Snapper riding mowers, the ID label is typically located in one of these spots:

• Under the seat pan (lift the seat and look on the frame)
• On the rear frame near the engine area
• Near the mower deck lift or footrest area
• On the left or right side of the chassis rail

Write down both the model number and the serial number exactly as shown.

Snapper serial numbers are commonly date-coded, but the exact format can vary by production run. Use this process:

• Look for a date stamp or a date-coded sequence within the serial number
• Check for a 2-digit year (YY) or a month and year pattern
• Compare what you see to the identification information in the owner's manual

Knowing the year helps us match the correct parts and specifications for your Snapper 355ZB2654, especially for wear items and assemblies that can change across production runs (for example, electrical components, wheels, and drivetrain hardware).

When ordering, always match parts to the full model number and serial number range. If you are servicing the drivetrain or motion system, confirm the exact transmission used before ordering a major assembly such as the transmission 5101027SM.

Last updated: February 2026

Yes. Snapper mower parts are still available for the Snapper 355ZB2654 rear-engine riding mower; you can match and order replacement parts by model number and the exact part ID from the parts list, and confirm fitment details in the 355ZB2654 owner's manual.

Use your mower’s model number (355ZB2654) and then match the part by diagram location and part ID. This prevents ordering a look-alike that will not fit.

• Confirm the full model number on the mower’s ID label
• Compare the part name and part ID, not just the description
• Check whether your mower uses a specific engine or deck configuration
• Replace worn hardware (nuts, washers, lock washers) when you remove it
• Keep a record of what you replaced and when

Availability varies by part, but these are examples of parts currently listed for this Snapper model that customers often need during repairs or maintenance:

• Snapper wheel 1714760SM (wheel)
• Snapper bearing 2108202SM (bearing)
• Snapper exhaust gasket 690970 (exhaust gasket)
• Snapper wire harness 5402849SM (wire harness)
• Snapper briggs and stratton solenoid-4 pole 12 volt dc ( 1686981YP (starter solenoid)

Many “needs a part” symptoms come from routine wear or setup issues. For example, the manual calls out blade wear limits and safe blade handling practices; a bent, nicked, or dangerously worn blade should be replaced rather than forced back into service.

• Dull or damaged blades (poor cut, vibration)
• Loose fasteners around the deck and blade area
• Worn wheels or bearings (uneven cut, noise)
• Electrical starting issues (clicking, no crank)

Using the correct OEM-style part for your Snapper 355ZB2654 helps restore safe operation, reduces repeat failures, and keeps the mower cutting and driving the way it was designed to.

Last updated: February 2026

To tell the mower deck size on your Snapper 355ZB2654, measure the cutting width across the blade path (not the outside edge of the deck). The most accurate method is to measure blade tip-to-tip with the blades installed, then confirm the deck configuration in the owner's manual.

1. Park on a flat, level surface; set the parking brake; turn the key off and remove it.
2. Set the cutting height to a mid setting so you can access the deck safely.
3. Rotate the blades so they point side-to-side.
4. Measure the distance from the outside tip of the left blade to the outside tip of the right blade (or the widest blade-tip span for your deck).

• Measure the blade path; do not measure the plastic chute/deflector or deck overhang.
• If the deck has multiple blades, measure the widest tip-to-tip span across the full cutting path.
• Bent blades change the effective width and cut quality; check blades before relying on measurements.
• If you are measuring to fit through a gate, measure the mower’s overall width separately (tires and any folded deflectors can change that).

Deck size is the cut width; overall width is what must fit through tight spaces.

Knowing the true deck size helps us match the right deck-related parts and setup procedures (belt routing, leveling, and blade orientation). For example, the manual’s deck leveling steps rely on measuring blade tips to the ground on a level surface.

Use the owner's manual when you need:

• The exact deck configuration for your 355ZB2654
• Deck removal and installation steps (PTO disengage, hair pins, leveling links)
• Deck leveling targets (side-to-side tolerance and front-to-back pitch)

Last updated: February 2026