Kenmore 10657023601 side-by-side refrigerator Parts

To replace the ice maker in your Kenmore side-by-side refrigerator model 10657023601, we turn the ice maker off, shut off the water supply, remove the ice bin, swap the ice maker assembly, then restore water and power so the unit can cycle and refill normally. See the owner's manual for the exact shutoff switch location and operating notes.

Before you start (safety and prep)

• Unplug the refrigerator or switch off power at the breaker.
• Turn the ice maker OFF using the On/Off switch in the freezer (top right area on this style).
• Shut off the household water supply to the refrigerator.
• Empty and remove the ice storage bin from the freezer door.
• Protect the floor with towels; a small amount of water can drip from the fill tube/line.

Replacement steps (typical for this Kenmore 106 model)

1. Remove the ice bin and any shelves/bins blocking access to the ice maker.
2. Disconnect the ice maker wiring harness plug.
3. Remove the mounting screws; support the ice maker as the last screw comes out.
4. Transfer any reusable parts from the old unit to the new one if your replacement does not include them (for example, mounting bracket or wire shutoff arm, depending on version).
5. Install the new ice maker, tighten mounting screws, and reconnect the wiring harness.
6. Reinstall the ice bin and any shelves/bins you removed.
7. Turn water back on, restore power, then switch the ice maker ON.

Parts that commonly match this repair

What you’re replacing	What it does	Part to use
Ice maker assembly	Cycles and harvests ice cubes	Refrigerator ice maker assembly 2198597

After installation: what to expect

• First batch timing: most ice makers need several hours to begin producing ice after installation.
• Discard the first 1 to 2 batches of ice to flush the water path.
• If the bin does not fill, confirm the ice maker is ON and the freezer is cold enough.

Why it matters

A worn ice maker can stop cycling, leak into the ice bin, or produce small/hollow cubes. Replacing the complete assembly restores reliable ice production and helps prevent dispenser and bin issues.

Last updated: February 2026

For Kenmore model 10657023601 side-by-side refrigerators, the most common problems we see are no ice or slow ice production, warm temperatures from airflow issues, water leaks, frost buildup from defrost or door-seal problems, and new or louder operating noises. Many fixes start with airflow, cleaning, and basic checks in the owner's manual.

Most common issues and what usually causes them

• Not cooling or uneven cooling: blocked air vents, overloaded shelves, dirty condenser area, or an evaporator fan issue.
• Ice maker not working: water supply problem, frozen fill tube, or a failed ice maker module.
• Water dispenser slow or not dispensing: clogged water filter or low household water pressure.
• Water leaking: clogged/iced defrost drain, loose water line connection, or a seeping inlet valve.
• Excessive frost: door not sealing, frequent door openings, or a defrost system problem.
• Noisy operation: normal compressor/fan changes, items vibrating, or water valve cycling.

Quick checks we recommend first (fast DIY)

1. Confirm airflow: keep vents inside the refrigerator and freezer clear; don’t pack food tightly against vent openings.
2. Verify control settings: set the refrigerator to about 37°F and the freezer to about 0°F, then allow 24 hours to stabilize.
3. Listen for “normal sounds”: buzzing when the water valve fills the ice maker, gurgling during defrost, and fan/compressor pulsing can be normal.
4. Check the water filter: replace on schedule and flush several gallons after installing a new filter.

Parts that commonly solve these symptoms (when a part is needed)

Symptom	Common part to check/replace	Example part for this model
Slow water, poor taste/odor	Water filter	Genuine Kenmore refrigerator water filter EDR3RXD1
No ice, small cubes	Ice maker assembly	Whirlpool refrigerator ice maker assembly 2198597
No water to dispenser/ice maker	Water inlet valve	Refrigerator inlet valve W10408179
Frost buildup, warm temps	Defrost safety thermostat	Refrigerator defrost bi-metal WPW10225581

Why it matters

Most “big” refrigerator complaints (warm temps, leaks, ice issues) start as airflow or water-supply problems. Fixing those early helps protect the compressor, prevents food spoilage, and reduces repeat ice maker and dispenser failures.

Last updated: February 2026

To identify what Kenmore refrigerator you have, locate the model number on the appliance ID label, then match that number when looking up parts and documentation. For Kenmore model 10657023601, the model number is the key detail that ensures the right water filter, ice maker, and other replacement parts fit.

Where to find the model number label

Most Kenmore refrigerators place the model and serial label in one of these spots:

• Inside the fresh food (refrigerator) compartment on a side wall
• On the ceiling inside the fresh food compartment
• Behind or under a crisper drawer (you may need to slide the drawer out)
• Behind the lower kick plate or toe grille at the front

If the label is hard to read, use a flashlight and take a close-up photo; the model number is usually the boldest line.

What the model number looks like for Kenmore

Kenmore model numbers are typically a long number string (often with a 3-digit prefix). For parts lookup, we use the full model number exactly as printed.

What to capture	Example for this page	Why it matters
Model number	10657023601	Determines the correct parts diagrams and compatible parts
Serial number	(varies)	Helps identify production run details for service and fit checks

Why it matters for parts and troubleshooting

Using the exact model number prevents common ordering mistakes, especially on parts that look similar but mount differently.

Common model-specific parts people replace include:

• Genuine Kenmore refrigerator water filter EDR3RXD1
• Whirlpool refrigerator ice maker assembly 2198597
• Refrigerator inlet valve W10408179
• Refrigerator door closer cam WPW10329686

Quick tip if you are already on this model page

If your label matches 10657023601, use the parts list and diagrams for this model and keep the number handy for future repairs. For operating details and label location guidance, use the owner's manual.

Why it matters: A single digit off in a Kenmore model number can change the correct ice maker assembly, water inlet valve, or water filter style.

Last updated: February 2026