Bosch SHX3AR55UC/12 dishwasher Parts

No. Dishwashers are not all 55 cm deep; depth varies by style (built-in, integrated, portable) and by brand. For your Bosch dishwasher model SHX3AR55UC, use the installation cutout and depth requirements in the installation guide to confirm the exact fit.

Most dishwashers fall into a few common depth ranges; the key is whether you are measuring the cabinet opening, the dishwasher cabinet, or the depth including the door/handle.

• Built-in (standard 24-inch class): often around 55 to 60 cm cabinet depth
• Fully integrated models: commonly designed around a 55 cm cabinet depth, but not universal
• Freestanding/portable models: can be deeper due to top and rear clearances
• Depth with door open: always much larger and matters for aisle clearance

Use these checks before ordering parts or planning an install:

• Measure cabinet opening depth from the back wall to the front of the cabinet face
• Check for baseboard/toe-kick interference at the bottom front
• Confirm water line, drain hose, and power routing space behind the unit
• If you have a panel-ready door, allow for panel thickness and door swing

Depth is the dimension that most often causes fit problems: even a few centimeters can prevent the dishwasher from sitting flush, can pinch the drain hose, or can keep the door from opening smoothly. The SHX3AR55UC installation guide gives the exact cutout and clearance requirements for this Bosch model.

Last updated: January 2026

For Bosch dishwashers like model SHX3AR55UC, the most common service issue is a heating problem (water not heating or cycles running unusually long). This often traces to the heater circuit, which can involve the control board, heater, or sensors; use the SHX3AR55UC owner's manual to confirm the symptoms and indicators for your exact unit.

• Cycle time seems to run much longer than normal
• Dishes come out cool and still wet (poor drying)
• Detergent does not dissolve well
• The dishwasher stops mid-cycle or appears to “stall”
• An error code related to heating or temperature appears (model-dependent)

1. Reset power: Turn off the breaker for 5 minutes, then restore power and try a normal cycle.
2. Verify incoming water temperature: Most dishwashers perform best with hot water at the sink (typically around 120°F).
3. Clean filters and spray arms: Restricted flow can reduce heating performance and cleaning.
4. Check for error codes: Use the Bosch dishwasher error codes reference to match the display code to a likely cause.
5. Confirm the door is latching: A weak latch can interrupt heating and wash action; if the door will not reliably latch, the dishwasher door lock 00630783 is a common suspect.

When the dishwasher cannot heat water correctly, it affects cleaning, drying, and cycle timing. Fixing the root cause prevents repeat problems and helps protect the circulation system from running excessively long.

Last updated: January 2026

To help prevent a Bosch E25 error on your SHX3AR55UC dishwasher, we focus on keeping the drain path clear: clean the filters regularly, remove debris from the sump area, and make sure the drain hose is routed correctly so the dishwasher can pump water out freely.

E25 commonly points to a drain problem (restricted flow or a blockage) that keeps water from leaving the tub fast enough.

• Clean the filter assembly and rinse it with warm water; scrub off grease and food film.
• Check the sump area under the filters for glass, labels, bones, or twist ties.
• Run hot water at the sink for 30 to 60 seconds before starting a cycle to reduce grease buildup.
• Use the right detergent amount; too much can create residue that traps debris.
• Keep the drain hose from kinking, crushing, or sagging into a low spot.
• If you have a garbage disposal, make sure the disposal inlet is clear and the knockout plug was removed during installation.

If cleaning and hose routing do not stop the error from returning, a weak drain system component is a common next cause.

Preventing E25 is mostly about protecting the drain pump and keeping wash water from sitting in the tub. A clear drain path improves cleaning results, reduces odors, and helps the dishwasher finish cycles normally.

For model-specific filter removal, drain hose routing, and maintenance intervals, follow the SHX3AR55UC manual. For installation details that affect draining (high loop, air gap, disposal connection), use the SHX3AR55UC installation guide.

Last updated: January 2026

To force-drain a Bosch dishwasher like model SHX3AR55UC, cancel the cycle so the unit switches to its drain routine, then clear any standing water from the sump area if needed. For the exact button sequence for your control panel, follow the SHX3AR55UC owner's manual.

• Cancel the cycle: Press and hold the Cancel/Drain function (or the Start button used for cancel) until the dishwasher begins draining.
• Wait for the drain routine to finish: Most drain-outs run for roughly 1 to 2 minutes.
• Reset power if the controls are unresponsive: Turn the dishwasher off at the breaker for 1 minute, restore power, then try cancel/drain again.
• Remove water manually if needed: If the drain routine runs but water remains, bail out water and check the sump for debris.

A forced drain will fail if the dishwasher cannot move water through the drain path.

• Food debris blocking the sump or filter area
• A kinked, clogged, or incorrectly routed drain hose (high loop/air gap issues)
• A jammed or failed drain pump
• A control or door-latch issue preventing the drain routine from running

Standing water can cause odors, poor cleaning, and can overwork the drain pump. Forcing a drain is a good first step, but clearing the filter and drain path prevents repeat clogs.

• Use dishwasher not draining video for a step-by-step checklist (filters, hose routing, pump checks).

Last updated: January 2026