Kenmore 11060372710 dryer Parts

Your Kenmore dryer’s model number is printed on the appliance’s ID tag; once you find it, you can match parts and instructions to the exact unit. For this page, the model number format looks like 11060372710, which you should copy exactly as shown on the tag.

Where to find the model number tag

We most often see the Kenmore dryer model/serial tag in one of these spots:

• Inside the door opening on the front panel (door jamb area)
• On the back panel of the dryer cabinet
• Near the lint screen housing (depending on the design)
• Behind the lower front access panel on some models

For diagrams and location notes specific to your dryer style, use the 11060372710 owner's manual.

How to read the number (and why it matters)

Kenmore model numbers commonly start with a prefix that helps identify the manufacturing source and parts family. The most important thing is to use the full model number and, when possible, the serial number too.

What to write down

• Full model number (all digits, no spaces)
• Serial number (helps confirm production run and compatible revisions)
• Fuel type (gas vs. electric) if your tag indicates it
• Any suffix letters or additional codes printed near the model number

What you’re looking for	Example	Why we need it
Model number	11060372710	Ensures correct part fit and diagrams
Serial number	(varies)	Helps confirm version changes
Power type	Gas or electric	Affects heating and ignition parts

Quick tips to avoid ordering the wrong part

• Copy the model number directly from the tag, not from the control panel styling or marketing name.
• If a digit is hard to read, take a clear photo and zoom in.
• Use the model number when selecting common wear items like a dryer heating element WP3387747 or a dryer door switch WP3406107.

Why it matters

Kenmore dryers can look similar across multiple series, but internal parts (heating circuit, drum support, controls) can differ. Using the exact model number keeps troubleshooting steps and replacement parts aligned with your dryer.

Last updated: February 2026

On Kenmore dryer model 11060372710, we open the front panel by unplugging the dryer, lifting the top, removing the front-panel mounting screws, disconnecting the door-switch wiring, then lifting the panel up and off the lower retaining tabs. This exposes the drum, belt, and motor area.

Before you start (safety and prep)

• Unplug the dryer (or switch off the breaker).
• If it is a gas dryer, shut off the gas supply valve.
• Pull the dryer forward for working room.
• Wear cut-resistant gloves; cabinet edges are sharp.
• Keep screws organized by location.

Front panel removal steps (common Kenmore 110-style cabinet)

1. Remove the lint screen (if it sits on the top panel) and remove the lint-screen housing screws.
2. Release the top: slide a putty knife under the front corners to pop the spring clips, then lift the top.
3. Remove screws along the top edge of the front panel and any screws inside the door opening.
4. Unplug the door switch harness from the front panel.
5. Pull the front panel slightly forward, then lift up to unhook it from the bottom tabs/clips.

What to check while it is open

• Belt condition and routing over the idler pulley
• Drum support rollers for flat spots, wobble, or squeal
• Lint buildup near the blower housing and motor

What you notice	Likely cause	Common next step
Squeal or thump	Worn drum rollers	Replace roller(s)
Drum hard to turn	Seized roller or idler	Replace support parts
Runs but no heat	Heating circuit problem	Test heater, fuses, wiring

Parts that often come up

• Dryer drum support roller WPW10314173 (drum support; wear causes noise)
• Dryer idler pulley W10837240 (belt tension; wear causes squeal)

Why it matters

Removing the front panel correctly prevents bent cabinet panels and damaged door-switch wiring, and it helps you reinstall the drum and belt so the dryer runs smoothly.

For model-specific fastener locations, follow the 11060372710 installation guide.

Last updated: February 2026

Kenmore dryer model 11060372710 is a full-size dryer; most units in this class measure about 27 inches wide, 27 to 30 inches deep, and 38 to 44 inches tall depending on console style and whether you include the exhaust duct. For the exact cabinet dimensions and required clearances, use the 11060372710 installation guide.

How to measure your dryer correctly

Use a tape measure and record three numbers.

• Width: left side panel to right side panel
• Depth: front edge to back edge (measure again including the vent elbow if space is tight)
• Height: floor to the top of the cabinet (or top of the control console, if it sits higher)
• Door clearance: allow extra room for the door swing
• Vent clearance: leave space so the exhaust duct is not crushed

Minimum space and clearance guidelines

Your installation space matters as much as the cabinet size. The documentation for this Kenmore dryer calls out common clearance needs for airflow and safe operation.

Location	Typical minimum clearance	Why it matters
Front (in a closet)	1 inch	Air intake and door operation
Rear	5 inches	Room for venting and airflow
Closet door	Vented openings top and bottom	Prevents overheating and long dry times

Why it matters

Correct sizing helps prevent crushed venting, poor airflow, and longer dry times. It also makes sure the dryer can be leveled properly and that the door and lint screen area stay easy to access.

If you are planning a new install or moving the dryer, we recommend confirming electrical or gas requirements and the final placement details in the 11060372710 installation guide before you commit to the space.

Last updated: February 2026