Kenmore 10652574202 refrigerator Parts

For Kenmore refrigerator model 10652574202, the model number is printed on the model and serial number label inside the fresh food (refrigerator) compartment. We use that full model number to match the correct parts, diagrams, and instructions for your exact side-by-side refrigerator.

Check these common locations on Kenmore side-by-side refrigerators:

• Inside the refrigerator compartment on an interior side wall (most common)
• On the inside wall near the crisper area (sometimes behind or beside the lower drawers)
• Behind the base grille or kick plate area (varies by installation)
• Inside the freezer compartment on an interior wall (less common)

For the exact label location and what the tag looks like, use the 10652574202 owner's manual.

Kenmore model numbers are used to identify the exact design version of your refrigerator so we can select the right replacement parts (ice maker, water inlet valve, thermostat, door cam) and the correct installation and service procedures.

Use these quick checks so we match parts accurately:

• Write the model number exactly as shown (all digits, no spaces)
• Record the serial number from the same label
• Take a clear photo of the label before ordering parts
• If the label is hard to read, clean it gently with a damp cloth and dry it

A single digit difference can change which parts fit your refrigerator. Using the full model number helps prevent ordering the wrong ice maker assembly, water filter housing, or other refrigerator parts.

Last updated: February 2026

To replace the ice maker on Kenmore model 10652574202, we shut off ice production, remove the ice bin or bucket, disconnect the ice maker wiring and water fill tube, then install the new assembly and restart ice production. Use the 10652574202 owner's manual for the exact shutoff style and restart steps.

• Unplug the refrigerator or turn off power at the breaker.
• Turn the ice maker OFF (wire shutoff arm up, or switch to OFF depending on style).
• Shut off the household water supply to the refrigerator.
• Empty the ice bin or door bucket so it is lighter and easier to handle.
• Protect the freezer floor with a towel to catch any drips.

1. Turn the ice maker off (wire arm up, or switch to OFF).
2. Remove the ice bin or bucket so you can access the ice maker area.
3. Remove mounting screws holding the ice maker to the freezer wall.
4. Disconnect the wiring harness plug.
5. Loosen the fill tube connection (if present) and pull the ice maker free.
6. Install the new ice maker, reconnect the harness, and secure mounting screws.
7. Restore water and power; turn the ice maker back ON.

The manual procedure for cleaning the water system starts with turning the ice maker off, then restoring power and following the water-system cleaning steps in the 10652574202 owner's manual. This helps clear air and any debris from the line.

If you are replacing the complete assembly for this model, use the exact replacement listed for the unit: ice maker assembly - refrigerator ice maker by whirlpool 4317943.

A correctly installed ice maker (properly seated, connected, and restarted) prevents slow ice production, leaks at the fill connection, and dispenser issues caused by an improperly installed bin or bucket.

Last updated: February 2026

Most Kenmore side-by-side refrigerators are about 32 to 36 inches wide; for Kenmore model 10652574202, the exact cabinet width is listed in the 10652574202 owner's manual. Use that measurement (not the door-to-door span) when planning a cutout or checking doorway clearance.

Side-by-side refrigerators commonly fall into these width ranges:

• 32 to 33 inches: space-saving models
• 35 to 36 inches: most full-size side-by-sides
• 36+ inches: select larger-capacity or premium designs

For accurate fit, we measure the refrigerator in two ways:

• Cabinet width: main box, excluding handles (best for cutout planning)
• Overall width: includes doors and sometimes trim
• Door swing clearance: extra space needed so doors open fully
• Installation clearance: space around the unit for airflow

The 10652574202 installation guide also calls out clearance needs; many side-by-sides require about 1/2 inch on each side and at the top for ventilation, plus extra room near a wall so the doors can swing.

A refrigerator that is even 1 inch too wide can bind in the opening, restrict airflow (warmer temps, more run time), or prevent the doors from opening far enough to slide out bins and shelves.

Last updated: February 2026

Most Kenmore Elite refrigerators average 10 to 15 years of service life with normal household use. For a Kenmore side-by-side like model 10652574202, regular care (cleaning, good door sealing, and stable temperatures) is what most often determines whether it lands closer to 10 years or closer to 15+ years; see the 10652574202 owner's manual for model-specific care steps.

In real-world use, we see these common ranges:

• 10 to 15 years: typical for most modern refrigerators
• 15 to 20 years: achievable with consistent maintenance and fewer sealed-system issues
• Under 10 years: most often tied to heavy use, poor airflow around the cabinet, or expensive cooling-system failures

These are the biggest factors we recommend focusing on:

• Dirty condenser coils: forces longer run times and higher heat load
• Worn or dirty door gaskets: causes warm air leaks and frost, raising compressor runtime
• Poor door alignment: can prevent a full seal and create temperature swings
• Overpacked compartments: blocks airflow to the evaporator and vents
• Water and ice system issues: leaks or low flow can create nuisance problems that lead to bigger repairs

We recommend these habits for Kenmore side-by-side refrigerators:

• Clean condenser coils on a regular schedule (more often with pets)
• Keep door gaskets clean and verify the doors close squarely
• Set stable temps (avoid frequent dial changes)
• Keep vents clear in both the freezer and fresh-food sections
• Address water/ice symptoms early; a failing refrigerator inlet valve W10408179 can cause slow fill or no ice on many setups

A refrigerator’s most expensive repairs are usually tied to the cooling system. Reducing heat load (clean coils) and preventing air leaks (good gaskets and alignment) directly reduces compressor runtime, which is the main driver of long-term wear.

Last updated: February 2026

Your Kenmore refrigerator model 10652574202 has an approximate total capacity of 21.9 cubic feet. For the exact capacity and how it is allocated between the refrigerator and freezer sections, we recommend confirming in the 10652574202 owner's manual.

Even with the same model number, usable space can vary slightly based on installed bins, shelves, and the ice storage configuration.

• Check the specifications section in the 10652574202 owner's manual
• Verify whether the ice maker and ice bin are installed (they reduce usable freezer space)
• Confirm all shelves and drawers are the correct OEM parts for the model
• Make sure door bins and crisper/meat pans are seated correctly

Capacity is the total internal volume measured under standardized conditions. Usable space is typically a bit less once you account for:

• Ice maker and ice bin
• Shelving supports and air ducts
• Crisper and meat pan assemblies
• Water filter housing (if equipped)

Knowing the cubic feet helps us match the right Kenmore replacement parts (like shelves, drawers, and ice storage components) and helps you compare storage expectations if you are troubleshooting temperature control, airflow, or overpacking issues.

Last updated: February 2026

You can find the model number for your Kenmore refrigerator on the model and serial number label inside the fresh food (refrigerator) compartment; on Kenmore model 10652574202, it’s on an inside wall of the refrigerator compartment. Use that full model number when ordering parts or looking up service information in the 10652574202 owner's manual.

• Open the refrigerator (fresh food) door and look along the inside side walls
• Check near the top front frame just inside the door opening
• Look behind or beside the crisper drawers on the interior liner
• Use a flashlight; the label is often small and easy to miss

Record these exactly as shown on the label:

• Model number (for example: 10652574202)
• Serial number
• Purchase date (if available)

Try these common alternate locations used on many side-by-side refrigerators:

• Behind the toe grille (kick plate) at the bottom front
• On the cabinet frame near the door hinge area
• On the rear exterior panel (less common)

Kenmore model numbers identify the exact configuration (ice maker, dispenser, wiring, and shelving). Using the correct model number helps us match the right replacement parts, such as the refrigerator inlet valve W10408179 or ice maker assembly 4317943, the first time.

Last updated: February 2026