Owner’s manual
Error Codes
What are the dimensions of a Kenmore elite?
Kenmore Elite dimensions vary a lot by style (top-mount, side-by-side, French door) and capacity. For the Kenmore Elite top-mount refrigerator model 10674202402, the exact height, width, and depth are listed in the 10674202402 owner's manual.
Typical Kenmore Elite refrigerator size ranges
If you are measuring for a kitchen opening, these are common ranges we see across Kenmore Elite refrigerators:
- Width: about 29 to 36 inches
- Height: about 66 to 70 inches
- Depth: about 30 to 35 inches (deeper with handles)
- Clearance needed: typically 1 inch on top and sides, plus room behind for airflow and water line routing
How to measure your refrigerator correctly
To avoid fit issues, we recommend measuring both the appliance and the space.
- Measure width at the widest point (often the hinge side)
- Measure height from floor to the top of the hinge cover
- Measure depth in two ways: cabinet only and cabinet plus handles
- Check door swing clearance so the doors can open fully
- Confirm the floor is level; leveling legs can change the final height slightly
Quick reference: what to record
| Measurement | What to include | Why it matters |
|---|---|---|
| Width | widest point (hinges) | prevents binding in the opening |
| Height | floor to top hinge area | avoids cabinet trim interference |
| Depth | with and without handles | ensures walkway and door clearance |
Why it matters
Correct dimensions help prevent installation headaches, improve airflow around the cabinet (better cooling efficiency), and reduce door-seal problems that can happen when a refrigerator is forced into a too-tight opening.
Last updated: January 2026
What does er ff mean on kenmore elite refrigerator?
On Kenmore Elite top-mount refrigerator model 10674202402, an ER FF code points to a freezer evaporator fan problem. That fan moves cold air through the freezer and into the fresh food section, so when it fails or is blocked, cooling performance drops.
What to check first (fast, no parts)
- Unplug the refrigerator for 5 minutes, then restore power to see if the code clears.
- Check for frost or ice buildup on the freezer back wall (a defrost issue can stop airflow).
- Make sure food packages are not blocking the freezer air vents.
- Listen for the evaporator fan: it should run when the compressor is running and the freezer door switch is pressed.
- Confirm the freezer door closes fully and the gasket seals (warm air leaks can cause icing).
Likely causes and the most common fixes
| What’s happening | What you’ll notice | Typical fix |
|---|---|---|
| Evaporator fan motor not running | Freezer may be cold, fridge warm; little airflow | Replace the fan motor |
| Fan blade damaged or rubbing ice | Clicking, scraping, or intermittent fan noise | Clear ice; replace blade if cracked |
| Heavy frost from defrost problem | Snowy frost on rear panel; airflow weak | Diagnose defrost system |
| Wiring/connection issue | Fan works sometimes; code returns | Inspect harness and connectors |
If the fan motor is the issue, the correct replacement for this model is the evaporator motor WP2315539. If the motor runs but airflow is noisy or inconsistent, inspect the fan blade WP2163777 for cracks or rubbing.
Why it matters
The evaporator fan is what distributes cold air. When it is stalled, iced in, or failing electrically, the refrigerator section often warms up first, and the compressor may run longer than normal.
Helpful manual guidance
We recommend using the 10674202402 owner’s manual to follow the model-specific troubleshooting steps and safety guidance before accessing internal panels.
Last updated: January 2026
Is there a way to reset a Kenmore Elite refrigerator?
Yes. For Kenmore Elite model 10674202402, the most reliable reset is to turn the refrigerator control to OFF, disconnect power, then restore power and set the control back to your normal setting; this clears many control-related glitches and restarts cooling.
Reset options that work on 10674202402
- Control reset (recommended): Turn the refrigerator control to OFF, unplug the power cord (or switch off the breaker), wait about 5 minutes, then restore power and set the control to the desired setting (steps align with the safety and control guidance in the 10674202402 owner's manual).
- Digital-control reset (cooling issue): If your unit has digital controls and it is not cooling, turn the refrigerator off and back on to reset (also covered in the 10674202402 owner's manual).
- After a power interruption: Restore power, confirm the control is not set to OFF, then allow up to 30 minutes for the refrigerator to resume normal operation after an automatic defrost or restart.
What to check right after you reset
- Make sure the refrigerator control is not set to OFF.
- Confirm the unit is plugged into a grounded 3-prong outlet (no extension cord).
- Check the house breaker/fuse if the refrigerator is completely dead.
- Verify air vents are not blocked by food packages.
- Listen for normal fan and compressor sounds; some noise is normal after restart.
Common symptoms and what a reset helps (and what it does not)
| Symptom | Reset may help | Also check |
|---|---|---|
| Not cooling after a glitch | Yes | Airflow, control settings, door closing |
| Lights not working | Sometimes | Bulb, door switch, outlet power |
| Runs a lot after loading groceries | No | Allow several hours to stabilize |
| Water in defrost drain pan | No | Normal during/after defrost |
Why it matters
A proper reset restores normal control operation and helps you avoid unnecessary parts replacement. If cooling does not return after a reset and basic airflow checks, the issue is usually in a component such as the evaporator fan system (motor or blade) rather than a simple control glitch.
Last updated: January 2026
How to tell cubic feet of Kenmore refrigerator by model number?
For Kenmore Elite model 10674202402, the model number by itself usually does not state the exact cubic-foot capacity. The most reliable way is to look up the capacity in the 10674202402 owner's manual; if you need a quick estimate, calculate interior volume from measurements.
Fast ways to find (or estimate) cubic feet
- Check the manual first: capacity is typically listed with other specifications in the 10674202402 owner's manual.
- Look for the rating label: many refrigerators list capacity on the model/serial tag inside the fresh-food section (often on an inside wall).
- Estimate by measuring (good for a ballpark): measure usable interior space and convert to cubic feet.
- Use the full model number: when searching specs, always use the complete number 10674202402 (not just “106.7420”).
How to calculate cubic feet from measurements
- Empty the compartment enough to measure.
- Measure width x depth x height of the usable interior space in inches.
- Multiply to get cubic inches.
- Divide by 1,728 to convert to cubic feet.
| What you measure | Use this | Notes |
|---|---|---|
| Fresh-food compartment | W x D x H | Exclude door bins if you want “shelf space” only |
| Freezer compartment | W x D x H | Measure below the ice maker area if equipped |
| Total estimate | (Fresh-food + freezer) / 1,728 | This is an approximation, not a rated spec |
Why the model number is not a reliable “capacity code”
Kenmore model numbers (including the 106 prefix used on many Kenmore refrigerators) identify the product line and configuration, but they do not consistently encode cubic-foot capacity in a way you can decode accurately at home. The rated capacity is a published specification, not a simple math conversion from the model digits.
Why it matters
Knowing cubic feet helps you compare replacement refrigerators, choose the right storage accessories (like a crisper pan), and set realistic expectations for shelf and freezer space.
Last updated: January 2026
