Kenmore 10655622500 side-by-side refrigerator Parts

Most Kenmore side-by-side refrigerators like model 10655622500 stand about 67 to 70 inches tall (without adding extra clearance). For the exact installed height and required clearances for your kitchen opening, use the measurements and diagrams in the 10655622500 owner's manual.

Measure in inches with a tape measure, and confirm the floor is level.

• Cabinet height: floor to top of refrigerator case
• Hinge height: floor to the highest hinge cover or hinge point (often the true max height)
• Door swing clearance: space needed so doors open fully
• Top and side ventilation space: needed for airflow and cooling performance
• Back clearance: extra room if you have an ice maker water line

Even if the refrigerator cabinet height fits, you still need clearance for ventilation and door swing.

• Plan for about 1/2 inch of space on each side and at the top for ventilation.
• If installed next to a fixed wall, plan for about 2 inches minimum on the hinge side (varies by setup) so the door can swing open.
• If the unit has an ice maker, allow extra space at the back for the water line connection.

These are common ranges for many counter-depth style side-by-side models.

A refrigerator that is “tall enough to fit” can still be a problem if the hinge height hits a cabinet, if the doors cannot swing open, or if there is not enough ventilation space. Correct clearance helps prevent poor cooling and nuisance door alignment issues.

Last updated: February 2026

Kenmore refrigerators typically last 10 to 15 years on average. For a Kenmore 10655622500 side-by-side refrigerator, consistent maintenance (cleaning, good airflow, and tight door seals) and timely repairs are what most often push real-world life closer to the high end of that range; see the 10655622500 owner's manual for care guidance.

• Average expected life: 10 to 15 years
• Often achievable with good care: 15 to 20 years
• Shortened lifespan is common when: condenser coils stay dirty, doors do not seal, or the unit runs hot in a tight enclosure

We recommend focusing on the items that reduce run time and heat load on the sealed system:

• Clean condenser coils and keep the toe-kick/base area clear of dust
• Confirm doors close fully and gaskets seal all the way around
• Keep freezer vents unblocked so air can circulate
• Set stable temps (avoid extreme cold settings that force constant running)
• Address ice maker and water leaks quickly to prevent corrosion and ice buildup

When cooling performance drops, these parts are frequent contributors on side-by-side refrigerators:

• Refrigerator thermostat WP2198202 (temperature control issues)
• Refrigerator defrost bi-metal WPW10225581 (defrost termination and frost control)
• Refrigerator heater WP2323198 (defrost heater function)

A refrigerator usually fails early because it is forced to run too long or too hot. Basic care (cleaning, airflow, and sealing) reduces stress on the compressor and sealed refrigeration system, which are the most expensive areas to repair.

Last updated: February 2026

For Kenmore side-by-side refrigerator model 10655622500, the model and serial number label is located on the inside wall of the refrigerator compartment. Use the model number from that label when ordering parts or checking instructions in the owner's manual.

• Open the fresh food (refrigerator) door
• Look on the inside wall of the refrigerator compartment
• Check near the side walls around the crisper area or upper interior wall
• Use a flashlight to read small print
• Write down both the model number and serial number exactly as shown

The label typically includes the model number, serial number, and sometimes the purchase date. Having the exact model number helps match the correct diagrams and parts for your refrigerator.

Kenmore model numbers can look similar across different series; using the exact model number from the inside label prevents ordering the wrong ice maker, water valve, thermostat, or other refrigerator parts.

Last updated: March 2026