Owner’s manual
View engine
How to lubricate a tiller?
For the Craftsman 917291482 front-tine tiller, lubrication mainly means keeping the engine oil at the correct level and lubricating the external pivot points and moving linkages; the transmission is sealed and does not need routine lubrication unless it’s serviced (per the 917291482 owner’s manual).
Focus on wear points that move, pivot, or slide during operation:
- Engine crankcase oil (check before each use; change on the schedule in the manual)
- Tine control linkage and control lever pivots
- Wheel height and depth stake adjustment points (pins, holes, and pivots)
- Cable ends and cable pivot points (light oil only)
- Any exposed metal-to-metal joints that squeak or bind
The manual notes the transmission is sealed and will not require lubrication unless serviced. Avoid forcing grease or oil into the transmission area unless you are following a service procedure.
- Shut the engine off, let it cool, and disconnect the spark plug wire.
- Brush off dirt around pivots and linkages so grit does not turn into grinding paste.
- Apply a few drops of light oil to pivots and cable ends; wipe off excess.
- If a pin is removed for adjustment, clean it and apply a thin film of oil before reinstalling.
- Reconnect the spark plug wire and test controls with the engine off first.
| Area | What to use | How much |
|---|---|---|
| Engine | Engine oil | Fill to proper level on dipstick |
| Pivots/linkages | Light machine oil | A few drops |
| Pins (wheel/depth stake) | Light oil | Thin film |
| Cables | Light oil (sparingly) | Wipe-on, wipe-off |
Proper lubrication reduces control stiffness, slows wear on moving joints, and helps prevent rust during storage. The manual also calls out lubricating the tiller before seasonal storage.
Last updated: January 2026
How to use a tiller with front tines?
On the Craftsman 917291482 front-tine tiller, we set engine speed with the throttle, then engage the forward tine control to start tine rotation. We control forward speed and digging depth mainly with the depth stake, wheel position, and handle pressure; see the 917291482 owner's manual for control locations and adjustments.
- Wear eye protection and sturdy shoes; keep children, pets, and bystanders away.
- Start the engine using choke only for a cold start; set throttle for starting.
- Let the engine warm up a few minutes before engaging the tines.
- Engage the forward tine control to start tine rotation; release it to stop the tines.
- Set wheel position and the depth stake for the soil and depth you want.
- Begin with throttle in a slow position until you are comfortable handling the tiller.
The depth stake acts like a depth limiter and a drag brake. More stake in the soil slows forward travel and increases digging.
| Adjustment | What it does | Best time to use |
|---|---|---|
| Lift handles slightly | Depth stake lifts a bit; moves forward easier | First pass, lighter soil, when it bogs |
| Press down on handles | Depth stake bites more; slows down; digs deeper | Deeper passes after breaking ground |
| Change wheel position | Changes stability and how the stake loads | When it bounces or pulls too hard |
- Never run the engine indoors; exhaust fumes are dangerous.
- Never operate without guards and shields in place.
- If tines catch and the tiller lunges forward, let go of the handlebars; do not restrain the machine.
- Before adjusting or cleaning, disconnect the spark plug wire and keep it away from the plug.
Correct wheel height and depth stake settings keep the tiller controllable, reduce bouncing, and prevent overloading belts, pulleys, and tine components.
Last updated: January 2026
Where is the model number on a Craftsman tiller?
On a Craftsman tiller, the model number is printed on the model-and-serial label; on model 917291482, it’s typically on the tine shield/guard area or on the engine/fuel tank area where the label is easy to see. Use the exact model number when ordering parts.
Check these common label locations before you start removing covers:
- On the tine shield (tine guard) near the front of the tiller
- On or near the engine, often close to the recoil starter housing
- On the fuel tank or the frame next to the tank
- On the handle column or control panel area
- On the main frame rail above the tines
The label usually includes a model number and may also include a serial number. For this tiller, the model is shown in the documentation as 917.291482 (you can write it as 917291482 when searching parts).
| Item to record | Example for this tiller | Why it matters |
|---|---|---|
| Model number | 917291482 | Ensures diagrams and parts match your exact unit |
| Serial number (if present) | Varies by unit | Helps confirm production run and correct revisions |
- Wipe dirt and oil off the frame and tine guard; labels are often hidden by grime
- Use a flashlight and look from the side of the tine shield
- Take a clear photo of the label before it fades further
- If the label is missing, use the 917291482 parts diagrams in the 917291482 owner's manual to identify assemblies (handles, belt guard, wheel and depth stake) and match parts by description
Craftsman tillers can look similar across years; using the correct model number prevents ordering the wrong belt guard, tine control parts, or wheel and depth stake hardware.
Last updated: January 2026
