Kenmore 11026912690 washer Parts

On the Kenmore washer model 11026912690, you turn Control Lock off by pressing and holding the same button that turns it on for about 3 seconds. The console typically labels that key with wording like “Control Lock” or “Hold 3 seconds.” See the 11026912690 owner's manual for the exact button on your control panel.

Steps to turn Control Lock off

• Make sure the washer is powered on.
• Look for a button labeled Control Lock or text that says Hold 3 seconds.
• Press and hold that button for 3 seconds.
• Release the button when the lock indicator light turns off (or the display changes).
• Try selecting a cycle and starting the washer to confirm the controls respond.

If it still will not unlock

These quick checks solve most “stuck lock” situations on Kenmore top-load washers:

• Press and hold longer: hold the key for a full 5 seconds.
• Pause and retry: wait 10 seconds, then press and hold again.
• Reset power: unplug the washer (or switch off the breaker) for 1 minute, then restore power and try again.
• Check for a jammed knob or key: make sure no button is physically stuck.
• Confirm you are using the correct key: some panels use a specific option key (not Start) to toggle the lock.

What Control Lock does (and why it matters)

Control Lock is designed to prevent accidental cycle changes, especially during agitation and spin. If it is on, the washer can appear “dead” even though power is present, which can lead to unnecessary part replacement.

Quick reference

What you see	What it usually means	What to do
“Control Lock” light on	Controls are disabled	Hold the Control Lock key 3 seconds
Controls do not respond	Lock is on or panel needs reset	Power reset, then hold key again

Ordering parts if you suspect a control issue

If the lock will not toggle after the steps above, the issue is usually in the console controls or timer circuit. You can look up replacement parts for model 11026912690 from the parts list for this model, or search by model number on Sears PartsDirect.

Last updated: February 2026

To unclog the drain hose on your Kenmore washer model 11026912690, unplug the washer, remove as much water as possible from the tub, then disconnect and clear the drain hose and pump inlet for socks, lint, and debris. Reassemble and test a drain and spin cycle.

Safety and prep (do this first)

• Unplug the washer to prevent electric shock.
• Turn off both water supply valves.
• Protect the floor with towels; keep a shallow pan handy.
• If the tub is full, bail water out or use a wet/dry shop vacuum at the standpipe.
• Review access and panel removal details in the 11026912690 owner's manual.

Step-by-step: unclog the drain hose

1. Check the standpipe first: Make sure the household drain is not backing up (a clogged standpipe can look like a washer problem).
2. Access the drain path: Pull the washer forward and locate the drain hose where it connects to the home drain and where it connects to the pump.
3. Clear the hose:
   • Remove the hose from the standpipe and inspect the end for lint buildup.
   • Disconnect the hose from the pump and look for obstructions.
   • Flush the hose with hot water; use a small drain snake or long zip tie to pull out debris.
4. Check the pump inlet and impeller area: Many clogs sit right at the pump inlet. If the pump is jammed, replacement is often the reliable fix.
5. Reinstall and test: Reconnect clamps securely, restore power, then run a drain/spin to confirm strong flow.

Parts that commonly solve “won’t drain” problems

Symptom	Most likely cause	Part to consider
Hums but won’t drain	Pump jammed or failed	Washer drain pump WP3363394
Drains slowly	Partial clog in hose or pump inlet	Hose cleaning; inspect pump
Fills but won’t advance	Drain issue affecting timer progression	Inspect drain path; timer only after drain is verified

Why it matters

A restricted drain hose or a jammed drain pump can prevent proper draining and spinning, leaving clothes wet and putting extra strain on the drive system. Clearing the blockage early helps prevent repeat clogs and reduces wear on components.

Ordering the right part

We list model-matched replacement parts for Kenmore 11026912690 on this page; you can also search by model number on Sears PartsDirect.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years. For the Kenmore 11026912690 (a classic top-load, agitator-style design), it’s common to see 15 to 20 years with normal household use and timely repairs; heavy use and overloading shorten that.

Typical lifespan by use

• Light use (1 to 3 loads/week): 15 to 20 years
• Average use (4 to 7 loads/week): 10 to 15 years
• Heavy use (8+ loads/week): 7 to 12 years
• Frequent overloading or unbalanced loads: cuts lifespan significantly

What usually fails first on model 11026912690

These are common wear items on older Kenmore top-load washers; replacing them often restores normal washing and spinning.

• Agitation problems (clothes not moving well): agitator dog 80040
• No spin or loud grinding during agitation/spin: coupling 285753A
• Weak spin, burning smell, or slipping during spin: clutch 285785
• Won’t drain or leaves water in the tub: washer drain pump WP3363394
• Off-balance shaking or banging: washer suspension spring WP63907

Quick maintenance that extends washer life

• Use the correct water level and avoid packing the basket tight.
• Keep loads balanced (mix items, do not wash one heavy item alone).
• Turn off water supply valves if the washer will sit unused for long periods.
• If you see slow filling, clean the inlet screens; a failing valve can be replaced with inlet valve 285805.
• Follow cycle and temperature guidance in the owner's manual.

Repair vs. replace: a simple guide

What you’re seeing	Most likely area	Typical next step
Agitator “ratchets” but won’t pull clothes through	Agitator dogs	Replace agitator dog 80040
Motor runs but washer won’t agitate/spin	Motor coupling	Replace coupling 285753A
Drains slowly or not at all	Drain pump or hose	Inspect/replace washer drain pump WP3363394
Loud mechanical noise in spin, oil leak underneath	Gear case	Inspect drive system; gear case replacement may be needed

Why it matters

Washer life expectancy is mostly about mechanical wear (drive system, clutch, pump) and load stress (overloading, chronic unbalance). On a durable platform like the Kenmore 11026912690, replacing a few key parts can add years of reliable service.

If you’re ready to repair, you can order model-specific replacement parts from the parts list for Kenmore 11026912690, or search by model on Sears PartsDirect.

Last updated: February 2026

Kenmore washer model numbers use a prefix plus additional digits to identify the design and exact version. For Kenmore model 11026912690, the 110 prefix identifies the manufacturing source used for many Kenmore top-load platforms; the remaining digits narrow it to your exact build.

How the number is typically structured

Most Kenmore washer model numbers break into three sections:

• Prefix (first 3 digits): identifies who built the washer for Kenmore (example: 110)
• Base model digits (middle group): identifies the core platform and major component family
• Suffix digits (ending group): identifies version details such as console, minor revisions, or feature packages

Quick breakdown example

Section	Example from 11026912690	What it tells us
Prefix	110	Manufacturer source/platform family
Remaining digits	26912690	Exact model variation for parts match

Where to find the model number on the washer

On Kenmore top-load washers like 11026912690, the model and serial tag is commonly located:

• Under the lid (along the rim of the opening)
• On the top frame near the tub opening
• On a label easiest to read with the lid open

For the exact location and labeling details, use the 11026912690 owner's manual.

Why the full model number matters for parts

Using the complete model number helps us match the correct diagrams and parts because small version changes can affect fit.

• Prevents wrong-part returns
• Ensures electrical and mechanical compatibility
• Speeds up troubleshooting and repair planning

If you are ordering common wear items for this washer, examples include the coupling 285753A and the washer drain pump WP3363394. You can also search by model number on Sears PartsDirect.

Why it matters

Kenmore washers can look similar across series, but internal parts like the gear case, clutch, timer, and inlet valve can vary by suffix.

Last updated: February 2026