Kenmore 11026432502 washer Parts

For Kenmore washer model 11026432502, a hard reset is a simple power reset: turn the washer off, unplug it for 1 minute, then plug it back in and restart a cycle. This clears minor control glitches and cycle interruptions.

Hard reset steps (power reset)

• Press the cycle control knob in to stop the washer.
• Unplug the washer from the wall outlet.
• Wait 60 seconds.
• Plug the washer back in.
• Close the lid.
• Select a cycle and pull the cycle control knob out to start.

If you want the exact stop and restart method for your control style, follow the steps in the 11026432502 owner’s manual.

If the washer still will not start or finish a cycle

A “reset” will not fix a failed safety switch, drain problem, or drive issue. Check these common causes next:

• Lid not sensing closed: the washer will not run or spin if the lid switch is not working.
• Not draining: a clog or weak pump can stop the cycle before spin.
• Unbalanced load: can cause repeated stops or poor spin.
• Timer not advancing: the cycle may stall at one point.
• Power supply issue: loose plug, tripped breaker, or bad outlet.

Quick symptom-to-part guide

Symptom	Most likely area	Example part for this model
Won’t run/spin with lid closed	Lid safety circuit	Washer lid switch assembly WP8318084
Won’t drain or drains slowly	Drain pump, hoses	Washer drain pump WP3363394
Cycle stalls or won’t advance	Timer/control	Washer timer WP8572976

Why it matters

A hard reset clears temporary electrical or control “hang-ups,” but it does not correct mechanical failures (like a drain restriction) or safety interlocks (like a lid switch). Using the right next check prevents repeat cycle stops and protects the drive system.

Last updated: February 2026

Your Kenmore washer model number is printed on the model and serial number label; for Kenmore model 11026432502, that label is located under the washer lid. Once you have the full model number, we use it to match the correct parts list, diagrams, and repair instructions for your exact washer.

Where to look on Kenmore model 11026432502

Check these common label locations in this order:

• Under the washer lid (most common for this style)
• Along the top rim of the washer opening (lift the lid and look around the frame)
• On the rear panel near the power cord entry
• Inside the control console area (less common)

For the exact label location and how the model and serial are formatted, use the 11026432502 owner's manual.

What the model number looks like (and what to write down)

Record the model number exactly as shown on the label.

Item to record	Example format	Why we need it
Model number	110.XXXXXXXX	Ensures parts fit your washer
Serial number	Letters and numbers	Helps confirm production details
Purchase date	Month/day/year	Useful for maintenance tracking

Tips to avoid ordering the wrong parts

These quick checks prevent the most common mix-ups:

• Copy every digit; do not drop leading zeros
• Use the full model number, not just “110”
• If the label is worn, take a clear photo with the lid open
• Match the model number before choosing common repairs like a lid switch, drain pump, or motor coupling

Why it matters

Kenmore washers share many similar-looking components across model families. Using the exact model number (like 11026432502) is what lets us select the correct Kenmore washer parts, including items such as a lid switch assembly, washer drain pump, or agitator components.

Last updated: February 2026

On Kenmore washer model 11026432502, a bad drain pump shows up as water left in the tub, a constant humming with little or no draining, or leaking at the pump area. First rule out a drain-hose setup problem (height, clogs, no air gap) before replacing the pump.

Quick checks we recommend first

• Confirm the lid is fully closed; this washer will not drain/spin with the lid open.
• Check the drain hose for kinks, crushing, or a clog.
• Verify the standpipe or laundry tub is not backing up (house drain can be the issue).
• Confirm the drain hose is installed with an air gap (do not tape or seal it to the standpipe).
• Measure detergent; excessive sudsing can slow draining and leave water behind.

What “normal” pump noise sounds like

Your manual notes that when the washer drains, the pump can make a continuous humming with periodic gurgling/surging as the last water leaves. Use this as a baseline when judging new noises. See the 11026432502 owner's manual.

Signs the pump is failing (not just a hose issue)

• Washer won’t drain or drains very slowly even with a clear hose and clear standpipe
• Loud grinding/rumbling from the pump area during drain
• Hums but does not move water (impeller slipping or motor weak)
• Water leaking at the pump body or pump connections

Drain hose setup specs to verify (from the manual)

Item to check	What to look for
Drain hose height	Top of hose at least 39 in. above the floor
Max drain height	End of hose not more than 96 in. above the floor
Standpipe fit	Hose fits securely but is not sealed; needs an air gap

When replacement makes sense

If the hose setup meets the height requirements, the lid switch is working, and the washer still leaves water behind with pump noise that is abnormal (or leaks at the pump), replacement is the next step. The correct part for this model is the washer drain pump WP3363394.

Why it matters

A weak or leaking drain pump can prevent proper spin, leaving clothes wet and increasing vibration and wear on drive components.

Last updated: February 2026

To unclog the drain hose on your Kenmore washer model 11026432502, unplug the washer, remove as much water as possible, then clear blockages from the hose and pump path. Reinstall the hose correctly so it does not kink and so it keeps an air gap at the standpipe.

Safety first and prep

• Unplug the washer (and turn off both water faucets if you will move it).
• Bail out water or use a wet/dry shop vac on the standpipe end of the drain hose.
• Keep towels and a shallow pan ready; hoses and the pump can hold water.
• If the washer is full, pause and let water cool before handling hoses.

Step-by-step: clear the clog

1. Check the standpipe or laundry tub first: remove the hooked end and confirm the household drain is not blocked.
2. Inspect for kinks and crushing: straighten the hose routing behind the washer.
3. Clear the hose: run warm water through the hose, then use a small drain snake or flexible brush to pull out lint, coins, or socks.
4. Check the pump area: clogs often sit where the hose meets the pump or inside the pump inlet.
5. If the washer still will not drain, the drain pump may be jammed or failing; replacing the pump is a common fix on this style of Kenmore washer.

Reinstall the drain hose correctly (prevents repeat clogs)

The installation instructions for model 11026432502 call out these key points:

• Do not straighten the hooked end of the drain hose.
• Do not force excess hose down into the standpipe.
• Keep the hose secure but loose enough to maintain an air gap.
• Rotate the hook to eliminate kinks.

For the exact clamp placement and hose seating depth at the cabinet drain connector, follow the 11026432502 installation guide.

Parts that commonly relate to “won’t drain” symptoms

Symptom	Most common cause	Part to consider
Hums but won’t drain	Pump jammed or worn	Washer drain pump WP3363394
Drains sometimes, slow drain	Partial hose or pump inlet clog	Drain hose and pump inlet check
Stops mid-cycle	Lid switch not sensing closed lid	Washer lid switch assembly WP8318084

Why it matters

A restricted drain hose makes the pump work harder, increases cycle time, and can leave water in the tub. Correct hose routing (no kinks, no forced standpipe insertion, proper air gap) prevents siphoning and repeat drain problems.

Last updated: February 2026

On Kenmore washer model 11026432502, the F25 code points to a problem with the washer sensing basket speed (a “spin/speed sensing” fault). The fix is usually checking the drive system and the wiring connections that let the control detect how fast the tub is turning; see the 11026432502 owner's manual for model-specific guidance.

What to check first (fast, no-parts steps)

• Unplug the washer for 1 minute, then restore power and retry a Spin/Drain cycle.
• Make sure the load is balanced and not overloaded; heavy items can cause erratic speed sensing.
• Confirm the washer is level and stable on the floor; excessive vibration can trigger sensing faults.
• Listen for abnormal sounds during spin (grinding, squealing, repeated start-stop).
• Inspect the lid closing action; if the washer thinks the lid is open, it may not spin normally.

Common causes and likely repairs

F25 is typically caused by a mechanical drive issue or an electrical sensing/connection issue.

What you notice	Most common cause	What we do next
Washer won’t spin or stops early	Lid switch not proving “closed”	Test/replace washer lid switch assembly WP8318084
Motor runs but tub barely moves	Worn drive coupling	Inspect/replace washer motor coupling 285753A
Agitation is weak or intermittent	Worn agitator dogs/cam	Inspect agitator dog 80040 and agitator cam 285748
Spins but bangs or walks	Suspension issue or unbalanced load	Check washer suspension spring WP63907 and leveling
Drains slowly, then won’t reach full spin	Drain restriction or weak pump	Check hoses; consider washer drain pump WP3363394

Why it matters

The control uses basket-speed feedback to ramp up safely into spin. When it cannot “read” speed correctly, the washer may stop to prevent damage to the drive system, clutch, gearcase, or basket.

Safety and setup notes

Before inspecting wiring or drive components, unplug the washer. If you need to move the washer or verify electrical grounding and outlet requirements, follow the 11026432502 installation guide.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years. For Kenmore model 11026432502, you can usually reach the high end of that range by keeping loads balanced, avoiding overloading, and following the care and use guidance in the 11026432502 owner's manual.

What affects washer lifespan the most

A washer’s service life is mostly determined by how hard it works and how well it’s maintained.

• Overloading (loads should move freely during washing)
• Unbalanced loads (extra strain on the drive system and suspension)
• Water quality (sediment can shorten inlet valve life)
• Detergent and bleach habits (avoid pouring chlorine bleach directly on fabrics)
• Wear items (couplers, clutches, pumps, lid switches)

Common wear parts that can shorten lifespan

When these parts start failing, the washer may stop agitating, stop spinning, or stop draining, which often leads to bigger problems if ignored.

Symptom	Commonly involved part	Example part for this model
Won’t drain or leaves water in tub	Drain pump or drain hose restriction	Washer drain pump WP3363394
Won’t spin or stops mid-cycle	Lid switch, clutch, drive components	Washer lid switch assembly WP8318084
Agitates poorly or “slips”	Agitator dogs/cam	Agitator dog 80040

Maintenance habits that help you reach 15 years

These are the same habits we see in long-lasting top-load Kenmore washers.

• Keep loads evenly distributed; mix large and small items
• Use the right water level for the load size
• Clean up bleach spills right away; never pour bleach directly onto clothing
• Check fill hoses for bulges or leaks and replace as needed
• Address new noises, burning smells, or slow draining early

Why it matters

A washer that is overloaded or consistently out of balance puts extra stress on the gearcase, clutch, motor coupling, and suspension. Reducing that stress is the simplest way to extend the life of Kenmore model 11026432502.

Last updated: February 2026