Kenmore 79094152310 electric range Parts

To reset your Kenmore electric range model 79094152310, we recommend doing a full power reset: turn the range off, shut off power at the circuit breaker for 1 to 5 minutes, then restore power and reset the clock and any oven settings. See the 79094152310 owner's manual for control and clock steps.

• Turn all surface element knobs to OFF.
• Turn the range OFF at the household circuit breaker (or remove the fuse).
• Wait 1 to 5 minutes to clear the electronic control.
• Restore power.
• Reset the clock and reselect your oven function (bake, broil, convection).
• If the oven was in use, confirm the oven begins heating normally.

Your range is designed to stop operating during a power failure; once power returns, you typically need to reset the clock and oven function.

• Clock display is correct
• Bake and broil start normally
• Surface elements heat and cycle
• No error code returns after a few minutes

If the display comes back but the oven will not heat, heats incorrectly, or shows an error again, the issue is usually in a heating or sensing circuit.

A proper reset clears a “stuck” electronic control state after a power interruption and helps you confirm whether the problem is a temporary control glitch or a failed component such as a sensor, element, or control board.

Last updated: January 2026

Your Kenmore stove’s model number is printed on a rating label attached to the range cabinet. On Kenmore electric ranges like model 79094152310, the label is most often found in the oven door jamb (open the oven door and look around the frame) or behind the lower storage drawer.

• Open the oven door and check the left and right door jamb area
• Pull out the bottom storage drawer and look on the frame behind it
• Check the back panel near the power cord entry area (if accessible)
• Look along the side frame near the front edge (door open helps)
• If your range is slide-in or tightly installed, use a flashlight and phone camera

The rating label usually includes the model number and serial number. For this Kenmore family, you may see a format like 790.9415* in the documentation, while the full model on the parts page is 79094152310.

Kenmore ranges can look similar across multiple model series, but parts like a bake element, oven temperature sensor, or surface element control switch can vary by model. Using the exact model number prevents ordering the wrong replacement part.

• Use the location diagrams and identification notes in the 79094152310 owner’s manual

Last updated: January 2026

A Kenmore electric range like model 79094152310 typically uses 30 to 50 amps on a dedicated 240-volt circuit; the exact amperage depends on the range’s total wattage and how it is wired. For the correct circuit requirement for your unit, follow the specs in the 79094152310 use & care guide and the 79094152310 installation guide.

Most electric ranges fall into one of these common setups:

• 30A: smaller or lower-wattage ranges
• 40A: very common for many 30-inch electric ranges
• 50A: higher-wattage ranges or models with more powerful elements
• Dedicated circuit required: ranges should not share a circuit with other appliances
• 240V supply: standard for electric ranges in the U.S.

If you find the wattage on the model/serial tag or in the installation specs, you can estimate current draw:

• Amps = Watts ÷ Volts
• Example: 9,600W ÷ 240V = 40A

Using the correct breaker and wire size helps your Kenmore range heat properly and prevents nuisance breaker trips, overheated wiring, and damage at the power connection.

If you are seeing error codes or odd heating behavior after a power issue, use our Kenmore 790 range 4-digit error codes guide to narrow down what the control is reporting.

Last updated: January 2026

Kenmore model 79094152310 is a Kenmore electric range built on the 790.9415* platform; this 790-prefix range family is manufactured by Frigidaire (Electrolux) for Kenmore. For confirmation details and the exact model series notation, check the 79094152310 owner's manual.

Kenmore uses a prefix system; the first three digits of the model number identify the original manufacturer.

• 790 prefix: Frigidaire-built Kenmore ranges
• The full model tag is typically found on the oven frame (often behind the storage drawer or along the door opening)
• Match the tag to the manual’s model family listing (for this unit, 790.9415*)

Knowing the manufacturer helps you choose the right style of parts and troubleshooting steps for your range.

These are examples of parts commonly associated with this platform.

• Frigidaire range oven temperature sensor 316490000 (helps correct inaccurate baking temperatures)
• Frigidaire range oven control board 316630003 (handles oven functions and error codes)
• Range bake element 316413800 (primary heat source for bake)

When we match parts and DIY steps to the Frigidaire-built Kenmore 790 platform, you get better fit, fewer returns, and faster troubleshooting for heating, controls, and self-clean features.

Last updated: January 2026