Kenmore 58715149401 dishwasher Parts

Yes, you can replace some parts on your Kenmore 58715149401 dishwasher yourself, but only if you can do the job safely. Always disconnect electrical power before servicing, and avoid touching the heating element during or right after use; use the 58715149401 owner's manual for safety and access guidance.

What you can usually DIY (and what to be careful about)

Many common repairs are straightforward, but water leaks and electrical issues raise the risk level.

• Good DIY candidates: rack rollers, door strike, door seal, some hoses and clamps
• Use extra caution: inlet valve replacement (water supply), drain pump work (water in sump)
• Usually technician-level: wiring harness troubleshooting, motor replacement, complex leak diagnosis
• Always do first: shut off power at the breaker, turn off water supply
• After any repair: run a short cycle and check for leaks

Parts on this model that are commonly replaced

These are examples of parts available for Kenmore 58715149401 that homeowners often replace.

Symptom	Likely part	Example part for this model
Water leaking at the door	Door seal or door alignment	Dishwasher door seal 809006501
Door won’t latch or pops open	Latch/strike issue	Strike 154662601
Not draining or drains slowly	Drain hose or drain pump	Hose 807117001
Dishes not drying well	Heating circuit issue	Heater 154665201

Safety and setup checks we recommend before you start

The installation instructions include a solid pre-start checklist that also applies after many repairs.

• Confirm the dishwasher is level and securely fastened
• Make sure the door opens and closes freely without hitting cabinets
• Verify water and drain lines have no kinks
• Confirm junction box wiring connections are tight
• Turn on water and check that joints are free of leaks

Why it matters

A dishwasher repair is usually a mix of water, sharp edges, and electricity. Following the manual’s safety steps helps prevent leaks, protects the door seal and tub from damage, and reduces the chance of burns from the heating element.

Last updated: February 2026

For Kenmore dishwasher model 58715149401, the fastest way to get the correct part number is to use the model and serial label on the dishwasher, then match that model to the exact part in our parts list. The label is typically on the inner door area.

Where to look for the model and serial label

Check these common spots on a Kenmore dishwasher like 58715149401:

• Along the inside edge of the door (left or right side)
• On the door frame around the tub opening
• Near the latch area on the inner door
• On the side of the tub opening (visible when the door is open)

If you need a diagram showing the label location and what the numbers look like, use the 58715149401 owner's manual.

How to use the label to get the right part

Once you find the label, use this process:

• Write down the full model number exactly: 58715149401
• Record the serial number too (it helps confirm production details)
• Identify the part you need by name (for example: door seal, drain hose, water inlet valve)
• Match the part name to the correct listing for your model
• Confirm the part number before ordering

Quick example (common parts customers replace)

What you are fixing	Part name to look for	Example part on this model
Water leaking at the door	Door seal	Dishwasher door seal 809006501
Not draining	Drain hose or drain pump	Hose 807117001 or drain pump A00126501
Not filling	Water inlet valve	Valve 154637401

Why it matters

Dishwasher parts are model-specific; even small design changes can affect fit, mounting holes, and electrical connectors. Using the model/serial label first prevents ordering the wrong Kenmore part and saves time on the repair.

Last updated: February 2026

You can identify your Kenmore dishwasher model by finding the model and serial number label on the inside edge of the door. On Kenmore model 58715149401, this label is typically visible when you open the door and look along the inner frame.

Where to look on the dishwasher

Check these common label locations first:

• Along the left side of the inner door frame
• Along the right side of the inner door frame
• On the top edge of the tub opening (near the latch area)
• Behind the kickplate area (less common for the model tag, but sometimes used for other labels)

For diagrams and the exact label callouts for this series, use the 58715149401 owner's manual.

What to write down (and why)

Record the full model number and serial number exactly as shown. That information is used to match the correct parts list, wiring, and installation details.

• Model number: identifies the exact dishwasher configuration
• Serial number: identifies the production run (helps with correct revisions)
• Purchase date: useful for service history and maintenance tracking

Quick example

Label field	What it does	Example format
Model number	Matches parts and diagrams	587.1514xxx
Serial number	Identifies build series	Letters and numbers

Why it matters

Kenmore dishwashers often share similar styling across multiple model families, but parts like the door seal, drain hose, and latch assembly can vary by model. Using the exact model number helps us point you to the right replacement part the first time.

Last updated: February 2026

Yes, repairing a Kenmore dishwasher like model 58715149401 is usually worth it when the problem is a normal wear part (seal, valve, pump, heater) and the tub and racks are still in good shape; you typically spend far less than replacement and avoid a full reinstall.

Quick way we decide: repair vs replace

• Repair when it’s leaking at the door, not filling, not draining, or not heating, and the unit otherwise runs normally.
• Replace when you have repeated major failures (motor, control issues), heavy rust, or chronic leaks from the tub area.
• Repair first if the dishwasher is under light to moderate use and you can fix it with one or two parts.

Common repairs on 58715149401 that often make sense

These are frequent, straightforward fixes that can restore performance:

• Door leak: replace the dishwasher door seal 809006501
• No fill or slow fill: replace the valve 154637401
• Not draining: inspect the drain path, then consider the dishwasher drain pump A00126501 if the pump is weak
• Poor drying or cool water: test/replace the heater 154665201
• Overfilling symptoms: check the float and float switch operation (the manual notes the overfill protector should move freely)

Cost and effort comparison (typical)

Scenario	Typical parts cost	Typical difficulty	When it’s “worth it”
Door seal leak	Low	Easy	No other issues, tub is sound
Fill/drain problem	Low to medium	Medium	One clear failure point
Heat/dry problem	Medium	Medium	Dishes clean but not drying
Motor or multiple issues	High	Hard	Only if overall condition is excellent

Why it matters

A targeted repair keeps your dishwasher reliable and can prevent secondary damage (for example, a door leak can worsen and affect flooring). The 58715149401 owner’s manual also emphasizes safe servicing practices, including disconnecting electrical power before service.

What to check before you buy parts

• Confirm household water pressure is in a normal range (the manual lists 20 to 120 psi).
• Confirm incoming hot water is at least 120°F (49°C).
• Look for the simplest failure first: loose hose connection, clogged drain air gap, blocked spray arm rotation.
• If the unit has been unused for 2+ weeks, run hot water at the sink first (hot water system safety guidance in the manual).

Last updated: February 2026

A Kenmore Elite dishwasher typically lasts 10 years with normal household use. Getting the full lifespan depends most on correct installation, steady water temperature, and routine cleaning of the filter area, spray arms, and door sealing surfaces (see the 58715149401 owner's manual).

Typical lifespan and what affects it

Most dishwashers land in a fairly tight range; the difference is usually maintenance and water conditions.

• Hard water shortens life by building scale on the heater and inside the sump
• Frequent heavy loads increase wear on the motor, pump seals, and racks
• Poor draining strains the drain pump and can leave standing water
• Overheating or low heat can affect cleaning and stress the heating circuit
• Door leaks can damage nearby components and flooring over time

Quick maintenance that helps you reach 10 years

These are the highest-impact habits for Kenmore model 58715149401 style dishwashers.

• Clean the sump area and remove debris that can block circulation
• Rinse spray arm holes if you see poor wash coverage
• Run hot water at the sink before starting a cycle to improve wash temperature
• Use the right detergent amount for your water hardness
• Inspect and wipe the door sealing surfaces; replace a worn seal if it drips

Common wear items vs. major repairs

Item type	Examples	What you’ll notice
Wear/maintenance	Door seal, rack rollers, hoses	Leaks, rough rack movement, slow drain
Major components	Motor, heater, drain pump	No wash action, no heat, won’t drain

If you’re seeing leaking at the bottom of the door, the dishwasher door seal 809006501 is a common fix on this model.

Why it matters

A dishwasher near end-of-life often shows up as longer cycles, weaker cleaning, or intermittent draining. Catching small issues early (like a minor leak or partial clog) helps prevent damage to the pump, heater, and wiring.

Last updated: February 2026

Kenmore dishwasher model 58715149401 is a standard built-in dishwasher size: it fits a 24-inch-wide cabinet opening and uses adjustable leveling legs to match common countertop heights. For the exact cutout and leveling targets for your kitchen, use the 58715149401 installation guide.

Typical dimensions and what to measure

Most 24-inch built-in dishwashers like the Kenmore 58715149401 are designed around standard cabinetry. What matters most is the cabinet opening height and the clearances for the door and hoses.

• Cabinet opening width: typically 24 inches
• Cabinet opening height: typically about 34 to 35 inches (adjusted with levelers)
• Depth: typically about 24 inches plus door thickness/handle clearance
• Leveling: front and rear legs adjust to match the opening

Installation fit details we use for this model

The installation instructions for this dishwasher focus on fitting the unit to the cabinet opening and adjusting the levelers so the dishwasher sits level and clears the underside of the countertop.

Fit check	What we look for	Why it matters
Opening height	Measure underside of countertop to floor	Determines how far to adjust levelers
Level side-to-side	Level across the tub front	Prevents leaks and poor washing
Level front-to-back	Level on the opened door edge	Helps proper draining and door sealing
Hose clearance	Keep drain hose away from sharp edges	Prevents kinks, rub-through, and leaks

Why it matters

Dishwashers can be “standard width” but still fail to fit if the opening height is tight, the floor is built up, or the unit is not leveled correctly. A correct fit also helps the door seal evenly and reduces the chance of water leaks.

Related parts that affect fit and sealing

If you are checking size because of leaking or door alignment, these parts are commonly involved:

• Dishwasher door seal 809006501 (helps stop leaks at the bottom/edges)
• Dishwasher door latch assembly A00104102 (helps the door pull in tight)
• Dishwasher door latch strike 154662601 (mates with the latch for proper closure)

Last updated: February 2026