Kenmore Elite 66513793K602 dishwasher Parts

Common problems on the Kenmore Elite dishwasher model 66513793K602 include poor cleaning, not draining, leaks, and a cycle that will not start or stops mid-cycle. Many issues trace back to loading and maintenance (filters, spray arms), power/door latch problems, or a failing pump, valve, or control.

Most common symptoms and what usually causes them

• Dishwasher will not run or stops: door not fully latched, wrong cycle selection, power interruption, tripped breaker or blown house fuse
• START/RESUME light flashing: door opened during the cycle or power was interrupted
• Not draining: clogged drain path, blocked hose/air gap, or a weak drain pump
• Not cleaning well: spray arm blockage, overloading, low water fill, or wash motor issues
• Leaking: door seal wear, loose hose connections, or tub and sump area leaks
• Spots/film on dishes: water chemistry, too much detergent, not enough rinse aid, or overloading

Quick checks we recommend first (fast, no parts)

1. Confirm the door closes tightly and latches.
2. Verify the cycle selection, then press Start and close the door promptly.
3. Check the home breaker or fuse; reset/replace if needed.
4. Make sure the water shutoff valve is fully open.
5. Clean for performance: run a vinegar cleaning cycle as described in the 66513793K602 owner’s manual.

Parts that commonly fix these problems on 66513793K602

Symptom	Common part to inspect/replace	What it affects
Won’t drain / standing water	Dishwasher drain pump WPW10348269	Pumps water out to the drain line
Won’t fill / fills slowly	Dishwasher water inlet valve (check screen)	Water entering the tub
Dead/no power symptoms	Fuse	Protects the dishwasher’s electrical circuit
Random behavior / won’t start	Electronic control	Runs cycles and responds to keypad inputs

Why it matters

Most “big” dishwasher complaints are caused by simple issues (door not latched, power interruption, clogged drain path) that can be corrected quickly. Catching a weak drain pump or inlet valve early helps prevent repeat cycle failures and water left in the tub.

Related help: Kenmore 665 model dishwasher error codes.

Last updated: January 2026

For Kenmore Elite dishwasher model 66513793K602, the most reliable hard reset is a full power cycle: turn the dishwasher off at the breaker (or unplug it) for about 5 minutes, then restore power. If you just need to clear a stuck cycle or lights, use CANCEL/DRAIN as shown in the 66513793K602 owner's manual.

Hard reset (power cycle) steps

• Turn the dishwasher OFF at the circuit breaker (preferred) or unplug it.
• Wait 5 minutes.
• Restore power.
• Press START/RESUME and close the door firmly to restart a cycle.
• If the control is still acting up, run a fresh cycle after clearing the previous one (steps below).

Clear the control panel and stop a cycle (manual method)

The Use and Care Guide for this model describes using CANCEL/DRAIN to clear selections and drain water.

• Open the door slightly and wait for spraying to stop.
• Press CANCEL/DRAIN.
• Close the door; the dishwasher runs a 2-minute drain (if needed).
• To clear indicators before starting over, press CANCEL/DRAIN before selecting a new cycle.

Which reset should I use?

Situation	Best action	What it does
Dishwasher is frozen or unresponsive	Power cycle (breaker off 5 minutes)	Reboots the electronic control
Wrong cycle/options selected	CANCEL/DRAIN, then reselect	Clears options and drains if needed
Door opened mid-cycle and lights are flashing	Press START/RESUME and close door firmly	Resumes the cycle

Why it matters

A true hard reset (power cycle) clears temporary control glitches, while CANCEL/DRAIN prevents starting a new wash with leftover water or a partially completed cycle. Using the right reset helps protect wash performance and avoids repeat drain or fill problems.

Last updated: January 2026

On Kenmore Elite dishwasher model 66513793K602, we clean the filter by removing the lower rack, lifting out the filter basket or screen assembly, rinsing it under hot water, then reinstalling it in the same orientation (it typically seats in place and locks with a short twist). See the 66513793K602 owner's manual for the exact filter style and removal steps.

Steps to clean the dishwasher filter

• Turn the dishwasher off; let it cool if it just ran.
• Pull out the lower rack to access the bottom of the tub.
• Remove the filter basket or screen (many Kenmore 665 models lift out, then rotate about 90 degrees to unlock or re-seat).
• Rinse the filter under hot running water; use a soft brush for stuck-on debris.
• Wipe the sump area around the filter opening; remove any glass or food pieces.
• Reinstall the filter so it sits flat and is fully locked or seated.
• Run a short rinse cycle to confirm normal wash and drain.

What to check while you are in there

If the filter was heavily clogged, also check these common related items:

What you notice	What it usually means	What to do next
Standing water after a cycle	Drain path restriction	Check the sink/disposer connection and drain hose routing; inspect the drain system
Grit on dishes	Filter not seated or torn, or spray arm issues	Re-seat the filter; clean spray arm holes
Bad odor	Food buildup in filter and sump	Clean filter and run a cleaning cycle (see tips below)

Why it matters

A clean, properly seated filter helps the wash system circulate water correctly and keeps food soil from redepositing on dishes. It also reduces drain problems that can strain components like the drain system.

Helpful cleaning tips (safe for most dishwashers)

• Rinse the filter weekly if you run frequent loads or wash heavy soil.
• Use a soft brush; avoid sharp tools that can tear mesh.
• For occasional film, we use a vinegar rinse sparingly (acid used too often can be hard on dishwasher components).

When a part may be involved

If the dishwasher still will not drain after cleaning the filter and checking the drain path, the drain pump can be the next suspect. For this model, the matching replacement is the dishwasher drain pump WPW10348269.

Last updated: January 2026

To force a drain on your Kenmore Elite dishwasher model 66513793K602, we recommend using the built-in CANCEL/DRAIN function; it runs a drain sequence for about 2 minutes (if needed) and clears the current cycle. See the 66513793K602 owner's manual for the exact button sequence.

Steps to force the dishwasher to drain

• Open the door slightly to pause the cycle.
• Wait until spraying stops.
• Press CANCEL/DRAIN (the Cancel light should turn on).
• Close the door to start the drain.
• Let it run for about 2 minutes.
• If you want to stop draining early, press CANCEL/DRAIN again.

If it still will not drain

A forced drain command will not help if water cannot physically leave the tub. These checks cover the most common causes on Kenmore 665-series dishwashers:

• Check the sink drain or garbage disposer connection for a blockage.
• Make sure the drain hose is not kinked or crushed behind the dishwasher.
• Confirm the drain hose routing stays clear of the motor, springs, cabinet edges, and flooring.
• Verify the high loop or air gap setup matches your installation method.
• If you hear the motor hum but no water moves, the drain pump may be jammed or failing.

Parts that commonly affect draining (when a repair is needed)

Symptom	Most likely area	Example part for 66513793K602
No drain sound at all	Drain pump or control issue	Dishwasher drain pump WPW10348269
Slow drain or leaks at hose	Drain hose routing or hose damage	Dishwasher drain hose 8269144A

Why it matters

Draining before starting a new cycle prevents dirty water from being recirculated, helps avoid odor, and reduces the chance of a false “not draining” situation caused by a paused or canceled cycle.

Last updated: January 2026