Frigidaire FFBD2412SS0A dishwasher Parts

For a hard reset on your Frigidaire FFBD2412SS0A dishwasher, we recommend turning off power at the breaker (or unplugging) for 5 to 10 minutes, then restoring power. If the controls are responsive, you can also cancel the cycle by holding START/CANCEL for 3 seconds.

• Turn the dishwasher off.
• Switch the dishwasher circuit breaker OFF (or unplug the power cord if accessible).
• Wait 5 to 10 minutes.
• Restore power.
• Close the door fully and press START/CANCEL once to reselect and start a cycle.

For model-specific operating notes, use the FFBD2412SS0A use & care manual.

The FFBD2412SS0A use & care instructions describe canceling a cycle by holding START/CANCEL for 3 seconds; the dishwasher runs a short drain (about 90 seconds) and then you can choose a new cycle.

• Press and hold START/CANCEL for 3 seconds.
• Let the drain finish.
• Select the next cycle and options.
• Press START/CANCEL to start.

A reset clears control glitches, but it will not fix a door that is not latching, a stuck overfill float, or a failed control.

Resetting the FFBD2412SS0A can clear a “stuck” cycle state after a power interruption or an interrupted wash. Using START/CANCEL first can also drain the tub, which helps prevent standing water and odor.

Last updated: January 2026

On the Frigidaire FFBD2412SS0A dishwasher, error code i20 is typically a drain problem (water not pumping out fast enough). We fix it by clearing restrictions in the filter area, drain hose, and drain path, then checking the drain pump if the unit still will not drain.

• Cancel the cycle and let the dishwasher run its drain (about 90 seconds on many Frigidaire models).
• Remove standing water (if needed) so you can inspect the sump area safely.
• Pull out the lower rack and check the filter area and glass trap for debris.
• Check the sink drain/disposer connection; make sure the disposer is empty and the inlet knockout plug is removed (if newly installed).
• Inspect the drain hose for kinks, crushing, or a sag that traps water.

For model-specific cleaning steps around the filter and glass trap, follow the FFBD2412SS0A use & care manual.

If you have good airflow through the drain hose and the dishwasher still will not drain, we move to the components most likely to cause i20:

• Drain pump (impeller jammed, worn, or electrically failed)
• Drain hose (internal blockage or collapsed hose)
• Check valve (stuck closed or blocked)

Common compatible parts for this model include:

• Drain pump a A00126401
• Dishwasher drain hose 807117001
• Dishwasher check valve 807048001

A true drain restriction can leave dirty water in the sump, trigger repeated i20 errors, and cause poor cleaning and odor over time. Clearing the drain path early often prevents a drain pump replacement.

Last updated: January 2026

For the Frigidaire FFBD2412SS0A dishwasher, the most common service issue we see is draining trouble (water left in the tub) caused by a clog in the filter/glass trap area, a kinked drain hose, or a weak drain pump. Poor cleaning and leaks are also frequent.

• Water left in bottom of tub: clogged filter/glass trap, blocked drain hose, drain pump issue
• Not cleaning well: spray arm blockage, low incoming water temperature, loading issues, detergent problems
• Leaking: door seal not seated, bottom door seal wear, unit not level
• Won’t start or stops mid-cycle: door latch not closing fully, control or user interface issue

For model-specific operating and “before you call” checks, use the FFBD2412SS0A use & care manual.

1. Cancel the cycle and let it drain; confirm the cycle is not paused.
2. Check and clean the filter area and glass trap (center of the tub).
3. Inspect the drain hose routing for kinks and make sure the high loop/air gap setup is correct.
4. Run hot water at the sink until it is hot before starting; this model expects about 120°F incoming water for best results.
5. Verify the dishwasher is level; an out-of-level tub can contribute to leaks and poor draining.

If cleaning and hose checks do not fix standing water, these model-compatible parts are common next steps:

A dishwasher that does not drain can leave dirty water in the sump, cause odors, and reduce cleaning performance on the next load. Catching clogs early also helps prevent strain on the drain pump and motor.

Last updated: January 2026