Kenmore 79090312012 electric range Parts

To reset your Kenmore electric range model 79090312012, we recommend doing a full power reset: turn the range off, cut power at the breaker for 5 minutes, then restore power and set the clock. This clears many control glitches and false error conditions.

Quick reset steps (power reset)

• Turn all surface element knobs to OFF.
• If the oven is running, press Cancel/Off on the control panel.
• Switch the range circuit breaker OFF (or unplug the power cord if accessible).
• Wait 5 minutes (10 minutes if the display was frozen).
• Restore power; set the clock and test Bake and Broil.

If the display shows an error code after reset

A reset clears temporary faults, but recurring codes usually point to a failed sensor, keypad, or control.

• Write down the exact code (letters and numbers).
• Try the reset once more.
• If the code returns, use our error-code guidance for Kenmore 790 ranges: Kenmore 790 range 4-digit error codes.

Parts that commonly cause “won’t heat” or temperature issues

If the oven still will not heat correctly after a reset, these model-compatible parts are common suspects:

Symptom	Most likely part	Example part for this model
Oven temperature is inaccurate or code relates to temp sensing	Oven temperature sensor	Frigidaire range oven temperature sensor 316490000
Bake does not heat but broil works	Bake element	Frigidaire range bake element 316413800
Broil does not heat	Broil element	Frigidaire range broil element 316203301

Why it matters

A breaker reset restores the electronic oven control to a known good state. If a fault returns immediately, the control is reacting to a real problem (often a sensor circuit or heating circuit), so replacing the correct part prevents repeat shutdowns and uneven cooking.

Safety note before troubleshooting

Because this is a 240-volt appliance, always shut off power at the breaker before removing panels or checking wiring. For wiring and grounding details (including terminal block cautions), follow the installation guide.

Last updated: January 2026

On the Kenmore 79090312012 electric range, an oven that “stops working” is usually caused by a power-supply problem (tripped breaker, loose terminal block connection), a failed oven temperature sensor, or a failed heating circuit (bake or broil). Start with power and wiring checks, then move to oven components.

Quick checks first (most common)

• Reset the range by turning the double breaker OFF for 1 minute, then back ON.
• Confirm the display has power; if the cooktop works but the oven is dead, focus on oven controls and sensors.
• Check for a loose or overheated connection at the power cord and terminal block area.
• If the oven stopped after a self-clean, suspect heat-related component failure (sensor, control, door lock circuit).
• If an error code is showing, use Kenmore 790 self-cleaning range error codes to pinpoint the circuit.

Power supply and wiring issues (high impact)

A range can appear “dead” or have an oven-only failure when the supply wiring is loose or damaged. The installation instructions stress secure terminal block connections and warn not to loosen factory-installed nuts that secure internal wiring.

What to inspect (power off at breaker):

• Terminal block screws and cord ends for discoloration or melting
• Strain relief tightness (cord not pulling on terminals)
• House cord condition (brittle insulation, burned ring terminals)

Symptom	Most likely area	What it points to
No display, no oven, no cooktop	Breaker, cord, terminal block	Loss of L1/L2 power
Cooktop works, oven won’t heat	Bake/broil circuit, sensor, control	Heating or sensing failure
Oven heats poorly or erratic temps	Sensor	Sensor out of range

Common failed parts on this model

• Oven temperature sensor: If the sensor reads wrong, the control may shut heating down or never heat correctly. Consider frigidaire range oven temperature sensor 316490000.
• Bake or broil element: A broken element can stop heating in that mode. For broil issues, consider frigidaire range broil element 316203301.
• Door lock circuit (self-clean models): A stuck lock can prevent operation; consider range oven door lock motor and switch assembly 5304528973.

Why it matters

An oven that stops working can be a simple reset, but loose terminal block wiring can cause repeated shutdowns and overheating. Checking power connections first prevents replacing good parts and helps restore safe, reliable heating.

For model-specific operating steps and any displayed codes, use the 79090312012 owner's manual.

Last updated: January 2026

On the Kenmore electric range model 79090312012, the model and serial label (serial plate) is typically on the lower right front frame of the appliance; an alternate location is under the cooktop. Use the label information to match the correct parts and instructions in the 79090312012 installation guide.

Where to check on the range

Look in these common spots first:

• Lower right front frame (open the oven door and check the front frame area)
• Under the cooktop (lift the cooktop if your design allows access)
• Behind the storage or warmer drawer (some ranges place the label on the frame behind the drawer)
• Rear panel area (less common, but worth a quick look)

Quick steps to find it fast

1. Turn the oven light on and open the oven door for better visibility.
2. Check the lower right front frame for a sticker or metal plate.
3. If you do not see it, check under the cooktop for the serial plate.
4. Write down the full model number and serial number exactly as shown.

What the label usually includes

Label item	What it’s used for
Model number	Ensures diagrams and parts match your exact range
Serial number	Helps confirm production series and compatible replacements
Electrical rating	Helps verify correct power cord/connection requirements

Why it matters

Kenmore ranges can look similar across multiple model series. Using the exact model number (79090312012) prevents ordering the wrong bake element, surface element control switch, or oven temperature sensor, and it helps you follow the correct safety and installation requirements.

Last updated: January 2026