Owner’s manual
View engine
Do Craftsman mowers use Briggs and Stratton engines?
Yes, many Craftsman mowers and lawn tractors use Briggs and Stratton engines, but it depends on the specific model and production run. For Craftsman model 917252451, the engine brand is identified in the 917252451 owner's manual and on the engine shroud data label.
Use these quick checks to confirm the engine manufacturer and model:
- Look for the engine ID label on the blower housing (shroud) or valve cover; it lists the engine make and model.
- Check the tractor frame tag for the tractor model (917252451) and compare it to the engine label.
- Use the engine model and type numbers when ordering engine-specific parts (filters, spark plug, carburetor items).
- Review the maintenance section in the manual for engine service items like oil type, spark plug, and air filter.
- If the tractor starts and runs poorly, confirm the engine ID first before troubleshooting fuel or ignition.
Craftsman has commonly paired their riding mowers and tractors with several engine brands over the years.
| Engine brand | Where you’ll usually see it | What to record for parts |
|---|---|---|
| Briggs and Stratton | Many Craftsman riders and push mowers | Model, type, code |
| Kohler | Some mid to higher horsepower riders | Spec number |
| Tecumseh (older units) | Older equipment | Model and spec |
Engine parts are matched to the engine model, not just the tractor model. Confirming the engine make helps you get the right tune-up parts (oil filter, air filter, spark plug) and speeds up troubleshooting for starting, stalling, or poor performance.
Last updated: January 2026
How much does it cost to replace a riding lawn mower engine?
For a Craftsman riding tractor like model 917252451, a full engine replacement typically runs about $800 to $2,500 total (engine plus labor), depending on engine brand, horsepower, and whether any pulleys, belts, or wiring need to be transferred or replaced. Use the 917252451 owner's manual to confirm engine specs and service guidance before ordering parts.
- Engine price: Most replacement riding mower engines fall in the $500 to $1,800 range.
- Labor time: Commonly 4 to 8 hours for a riding tractor engine swap.
- Extra parts: Worn belts, pulleys, or mounting hardware often get replaced during the job.
- Shop rates: Local labor rates vary widely.
- Condition of the tractor: Rusted fasteners, damaged wiring, or fuel system issues add time.
Even when the engine is the main issue, we often see related drive and deck components replaced to prevent repeat problems:
- V-belt 532138255 (ground drive belt)
- Lawn tractor drive belt 532144200 (blade drive belt)
- Fuel filter and fresh fuel lines (common wear items)
- Spark plug and air filter (basic tune-up parts)
- Battery service (clean/charge terminals as needed)
| Cost item | Typical range | Notes |
|---|---|---|
| Replacement engine | $500 to $1,800 | Varies by horsepower and shaft specs |
| Labor | $300 to $1,200 | Often 4 to 8 hours |
| Belts, filters, tune-up items | $25 to $200 | Depends on what is worn |
| Total installed | $800 to $2,500 | Most common real-world range |
An engine swap only pays off if the rest of the tractor is solid. If the deck, mandrels, steering, and transmission are in good shape, replacing the engine can restore years of service. If multiple major systems are worn, a replacement tractor can be the better value.
Last updated: January 2026
What engine does Craftsman riding mower use?
The Craftsman front-engine lawn tractor model 917252451 uses a single-cylinder gasoline engine (a common setup for this tractor style). For the exact engine manufacturer, displacement, and tune-up specs for your unit, match the engine information in the 917252451 owner's manual.
Use these quick checks so you get the right maintenance parts (spark plug, air filter, fuel filter) and correct oil type.
- Look for the engine ID label on the blower housing, valve cover, or near the starter
- Write down model, type, and code (common on Briggs and similar engines)
- Compare those numbers to the Product specifications section in the manual
- Use the manual’s maintenance pages for oil change intervals and spark plug service
- If the label is missing, use the tractor’s build details plus the manual’s specs to narrow it down
The manual for this tractor includes engine maintenance topics such as oil type and oil changes, air filter service, cooling fins, spark plug service, and a troubleshooting chart. That information is what you need to correctly service the engine even before you confirm the brand.
These are the most typical configurations you will see on tractors in this class; use them as a guide while you confirm the exact engine ID.
| What you’re checking | Most common on this tractor style | Where to confirm |
|---|---|---|
| Engine layout | Single-cylinder, vertical-shaft | Engine ID label and manual specs |
| Fuel system | Carbureted gasoline | Manual maintenance and tune-up sections |
| Starting system | 12V electric start | Manual operation and electrical sections |
Engine identification prevents wrong-part returns and avoids problems like hard starting, poor cutting power, or stalling caused by incorrect spark plug type, air filter fit, or oil viscosity.
Last updated: January 2026
