Kenmore Elite 66512773K314 dishwasher Parts

For Kenmore Elite dishwasher model 66512773K314, a “hard reset” is done by resetting the control with CANCEL/DRAIN. Press and hold CANCEL/DRAIN twice to reset, then reselect your cycle and press START/RESUME to restart.

Hard reset steps (control reset)

• Open the door slightly to pause the cycle; wait for spraying to stop.
• Open the door fully.
• If the detergent dispenser cover is open, refill detergent before restarting.
• Press and hold CANCEL/DRAIN twice to reset the control.
• Select the new cycle and options.
• Press START/RESUME, then close the door to begin.

For button locations and exact panel behavior on this model, follow the 66512773K314 owner's manual.

If the dishwasher still will not start after the reset

These checks solve most “won’t run” complaints after a reset:

• Make sure the door is fully closed and latched (no interference from large dishes).
• If the START/RESUME light is blinking, press START/RESUME and close the door within 3 seconds.
• Confirm a cycle is selected (some options are not available on every cycle).
• Check household power: breaker or fuse.
• If multiple lights blink and it will not run, service is typically needed.

What “hard reset” means on this model

Reset type	What it does	When to use it
Control reset (CANCEL/DRAIN)	Clears the current cycle and lets you restart from the beginning	Stuck cycle, wrong selection, needs restart
Cycle resume (START/RESUME)	Continues a paused cycle when the Start/Resume light is blinking	Door opened mid-cycle, interrupted cycle

Why it matters

Resetting with CANCEL/DRAIN helps clear a stalled cycle and forces the dishwasher to drain if water is in the tub, which prevents restarting a new cycle with leftover water and improves wash results.

Last updated: January 2026

For Kenmore Elite dishwasher model 66512773K314, we find the model number on the appliance’s rating label; it’s typically located just inside the door opening along the tub edge (often on the left side) and is printed with the serial number.

Where to look on the dishwasher

Check these common label locations first:

• Inside the door opening on the left tub wall (most common)
• Inside the door opening on the right tub wall
• Along the top edge of the tub opening (under the counter lip)
• On the inner door frame near the latch area

What the label looks like

The rating label is usually a small sticker or metal plate that includes key identifiers.

Label item	What it’s used for	Example for this page
Model number	Matching parts and diagrams	66512773K314
Serial number	Date/production tracking	Varies by unit
Electrical ratings	Install and troubleshooting reference	Varies by unit

Tips to make sure you capture the right number

Use these quick checks so you order the correct Kenmore parts (like a door latch, water inlet valve, or rack adjuster kit):

• Write the model number exactly as shown, including all digits and letters
• Take a clear photo before the label gets worn or smeared
• Clean the label gently with a damp cloth if it’s hard to read (do not use abrasives)
• Use the model number when checking instructions in the 66512773K314 owner’s manual
• If you’re installing or re-installing the unit, confirm requirements in the 66512773K314 installation guide

Why it matters

Kenmore dishwashers can look similar across series, but parts can differ by model revision. Using the exact model number helps us match the correct components and avoid returns or fit issues.

Last updated: January 2026

On the Kenmore Elite dishwasher model 66512773K314, a Start button that will not respond is usually caused by Control Lock being enabled, the door not fully latching, or the Start/Resume sequence timing out after the door is opened. Use the steps in the 66512773K314 owner’s manual to unlock controls and restart correctly.

Quick checks we recommend first

• Make sure Locked is not lit; when Control Lock is on, all buttons are disabled.
• Press and hold TOP RACK ONLY for 3 seconds to toggle Control Lock off.
• Close the door firmly until it latches; the dishwasher will not run if it is not latched.
• If the Start/Resume light is blinking, press START/RESUME and close the door within 3 seconds.
• If you opened the door for more than about 5 seconds during a delay start, press START/RESUME again to resume the countdown.

How Control Lock affects the Start button

Control Lock is designed to prevent unintended use between cycles. When it is enabled, the dishwasher cannot start.

What you see	What it usually means	What to do
“Locked” light on	Control Lock is enabled	Hold TOP RACK ONLY 3 seconds
Lights flash when you press pads	Controls are locked	Turn off Control Lock, then retry
Start/Resume blinking	Door was opened or start sequence interrupted	Press Start/Resume, close door within 3 seconds

If the door will not latch consistently

A weak or failing latch can make the Start button seem “dead” because the control will not begin the cycle until the door switch reads closed.

• Check for tall items (cookie sheets, cutting boards, large containers) preventing the door from closing.
• Re-load so nothing interferes with the wash system at the back of the tub.
• If the latch feels loose or does not “click,” consider replacing the dishwasher door latch WPW10653840.

Why it matters

The Start/Resume function on this Kenmore Elite dishwasher is tied to safety interlocks (Control Lock and door latch). Fixing the lock or latch issue restores normal starting and prevents mid-cycle interruptions.

Last updated: January 2026

Common problems on the Kenmore Elite dishwasher model 66512773K314 include not starting, not filling, not draining (water left in the tub), poor drying, detergent not dispensing, long cycle times, odors, and hard-water residue. Many issues trace back to door latching, power, loading, or drain-hose restrictions; see the 66512773K314 owner's manual for model-specific checks.

Most common symptoms and what to check first

• Dishwasher won’t run or Start/Resume light blinks: press Start/Resume and close the door within 3 seconds; confirm the door is fully latched.
• Won’t fill: confirm household power is on and the cycle is actually selected; then check for basic supply issues.
• Water remains in tub (won’t drain): check for kinks in the drain hose and food obstructions in the drain path.
• Detergent remains in dispenser: confirm the door closes without interference from large dishes; avoid blocking the dispenser area.
• Hard-water film or spotting: use rinse aid, use fresh detergent, and clean filters monthly.

Quick troubleshooting table

Problem	Most likely cause	Best first action
Won’t start	Door not latched or Start/Resume not completed	Press Start/Resume, close door within 3 seconds
Won’t drain	Kinked hose or blockage	Inspect drain hose routing and clear obstructions
Poor drying	No rinse aid or cycle/option choice	Fill rinse aid, use heated options when needed
White residue	Hard water	Monthly dishwasher cleaner, rinse aid, filter cleaning
Odors	Food soil buildup	Clean filters and run a cleaning cycle

Parts that commonly relate to these problems

If you confirm a mechanical failure (not just loading or settings), these parts are often involved:

• Door not closing or won’t start: dishwasher door latch WPW10653840
• Won’t fill or fills slowly: dishwasher water inlet valve WPW10327249
• Water left in tub: dishwasher drain pump WPW10531320 or dishwasher drain hose 8269144A
• Poor drying or no heat: element assembly W10703867

Why it matters

A dishwasher that does not latch, fill, heat, or drain correctly can leave detergent undissolved, extend cycle time, and cause odors or residue. Catching simple causes first (door closure, loading interference, hose kinks, filter maintenance) prevents unnecessary part replacement.

Last updated: January 2026