Kenmore 79046783905 electric range Parts

Most Kenmore ranges are 30 inches wide, and the Kenmore 79046783905 slide-in electric range is designed for a 30-inch cabinet opening; its cooktop rim is about 31 7/8 inches wide so it can overlap the countertop edges. For the exact fit notes, use the installation guide.

Model-specific width details (Kenmore 79046783905)

Here are the key width measurements we use for planning a cutout and confirming fit:

Measurement type	Typical use	Measurement
Cabinet opening (base cabinets)	Space between cabinets	30 in (76.2 cm)
Countertop cutout width	Opening in the countertop	30 1/16 in (76.4 cm)
Cooktop rim width (overlap)	Top rim that sits over countertop edges	31 7/8 in (79.5 cm)

How to measure your space correctly

• Measure the cabinet opening width at the front and back.
• Measure the countertop cutout width (if it is already cut).
• Confirm there is clearance so the cooktop rim can overlap the countertop edges.
• Check that cabinets and countertop are plumb and level; a range that is not level can bake unevenly.
• If you have a formed or tile countertop, plan for trimming at the front corners so the rim sits flat.

Why it matters

Range “width” can mean the cabinet opening, the countertop cutout, or the cooktop rim. For slide-in models like the Kenmore 79046783905, the cooktop rim is wider than the cabinet opening by design, so the range can sit cleanly over the countertop edges.

Last updated: January 2026

On Kenmore electric range model 79046783905, the model number is printed on the serial plate, which is typically on the oven front frame behind the oven door or behind the bottom drawer (depending on the exact configuration). Confirm the exact location in the 79046783905 installation guide.

Where to look first (fastest checks)

• Open the oven door and look along the front frame (the area the door closes against).
• Pull out the bottom drawer and check the frame behind the drawer opening.
• Check for a silver or white serial plate label with both model and serial numbers.
• Use a flashlight; labels are often low and partially shaded.

What the serial plate label looks like

Most Kenmore ranges use a single label that includes the model number, serial number, and sometimes a lot number/letter.

What you need	What it’s used for	Where it’s found
Model number (79046783905)	Matching parts and diagrams	Serial plate label
Serial number	Service history and identification	Serial plate label
Lot number/letter (if shown)	Parts and service inquiries	Serial plate label

Why it matters

We use the full model number to match the correct parts (like a bake element, control panel, or oven temperature sensor) because similar Kenmore ranges can use different wiring, elements, and control components.

Tips if the label is hard to read

• Wipe gently with a damp cloth and mild soap; avoid abrasive cleaners.
• Take a close-up photo and zoom in.
• Write the model and serial numbers down exactly as shown.

Last updated: January 2026

To reset a Kenmore range model 79046783905, we recommend doing a full power reset: turn the range off, shut off power at the breaker for 5 minutes, then restore power and set the clock. This clears many control glitches and false error displays.

Quick reset steps (most common)

• Turn all surface burners and oven functions to OFF.
• Switch the range circuit breaker OFF (or remove the range fuse).
• Wait 5 minutes.
• Switch the breaker ON.
• Set the clock and test Bake and Broil.

For control-specific steps and any model-specific display behavior, use the 79046783905 owner's manual.

If the display shows an error code after the reset

A reset can clear a temporary fault, but repeated codes usually point to a component or wiring issue.

Common next checks:

• If the oven temperature seems inaccurate, inspect the sensor circuit and consider the range oven temperature sensor 5304504897.
• If the oven overheats or shuts down during high heat, a limit device can be involved (for example, the frigidaire range high-limit thermostat 318578506).
• If the code returns immediately after power-up, check for a stuck key on the control panel and any loose harness connections.

For code definitions and what each one means on Kenmore 790 ranges, use Kenmore 790 self-cleaning range error codes.

What a reset does (and does not do)

Action	What it helps	What it will not fix
Breaker reset (power cycle)	Frozen display, random beeping, minor control glitches	Failed heating element, failed sensor, damaged wiring
Clock re-set	Restores normal timed functions	Temperature calibration problems

Why it matters

A proper power reset is the fastest way to rule out a temporary electronic control issue before replacing parts like the oven temperature sensor, thermostat, or control panel.

Last updated: January 2026