Kenmore Elite 66513943K011 undercounter dishwasher Parts

Yes. Kenmore dishwashers like model 66513943K011 are designed to run quietly, but you will still hear normal operating sounds such as draining surges, brief water-valve hissing, and the detergent dispenser snapping open. Installation and loading issues are the most common reasons a unit seems louder than expected.

Even a quiet dishwasher is not silent. These sounds are considered normal during a cycle:

• Surging or whooshing while the dishwasher drains
• Hissing from the water inlet valve as it fills
• A snap/click when the detergent dispenser opens
• Light motor and spray sounds as water circulates

These sound notes are called out in the 66513943K011 owner’s manual.

If the sound is a thump, rattle, or grinding, we focus on the simple causes first:

• Make sure no plates, utensils, or tall items extend into the spray path
• Reposition the load if you hear thumping (items can hit the wash arms)
• Confirm the filters are seated correctly after cleaning
• Check that the dishwasher is level and secured to the cabinet
• Verify hoses and wiring are routed so they do not contact the motor or legs

Improper installation can raise noise levels, and the installation guide also warns against routing lines where they can interfere with the motor area; see the 66513943K011 installation guide.

A dishwasher that is installed level, loaded correctly, and has properly seated filters runs quieter and cleans better. Many “noise complaints” are actually spray-arm interference or installation contact points that are easy to correct.

Last updated: January 2026

To identify your Kenmore dishwasher model, open the door and look for the model and serial tag on the tub rim or inner door area; for Kenmore Elite model 66513943K011, this tag is the key detail you need for correct parts and instructions in the 66513943K011 owner's manual.

Check these common label locations first (in order):

• Along the tub opening (top edge of the tub, near the door seal)
• On the left or right side wall of the tub, near the front
• On the inner door frame (door jamb area)
• Behind the lower access panel (less common)
• On older units, a faded sticker may be tucked near the hinge area

For Kenmore dishwashers, the model number is usually a long string of numbers and letters.

Using the exact model number prevents ordering the wrong rack parts, pump, or valve. For example, common wear items for this model include rack hardware and water or drain components such as the dishwasher water inlet valve W11175771 and the dishwasher drain pump WPW10348269.

• Wipe the tag gently with a damp cloth to remove film and detergent residue
• Use your phone camera and zoom in; angled light often makes faded print readable
• Copy the model number exactly, including all letters and the full suffix

Last updated: January 2026

Common problems on the Kenmore Elite 66513943K011 dishwasher include not starting or stopping mid-cycle, not filling, not draining (water left in the tub), poor cleaning, and drying complaints. Most of these trace back to loading issues, water supply problems, drain restrictions, or a worn wash system part; use the 66513943K011 owner's manual troubleshooting chart to narrow it down fast.

• Dishwasher does not run: door not fully latched, Start/Resume needs to be pressed again, cycle not selected, or a tripped breaker.
• Will not fill: water supply valve turned off, float stuck, or excess suds/foam.
• Water remains in tub / will not drain: kinked drain hose, disposer knockout plug not removed, or a clog in the drain path.
• Food soils remain on dishes: improper loading, dirty or misinstalled filter, low incoming water temperature, or blocked spray action.
• Drying issues: loading that traps water (concave bottoms), or cycle/option selection that reduces heat.

1. Confirm the door closes and latches without hitting tall items in the back of the tub.
2. If the Start/Resume light is blinking, close the door and press START/RESUME.
3. Verify the house breaker or fuse is on.
4. Make sure the water supply to the dishwasher is fully turned on.
5. Inspect the drain hose routing for kinks and confirm the sink disposer inlet knockout plug was removed (if connected).
6. Check the filter is installed correctly and clean it if needed.

Dishwasher problems often look “electronic,” but the manual’s checks focus on basics that cause most service calls: door closure, water supply, drain restrictions, and correct loading. Fixing those first prevents unnecessary part replacement and repeat clogs.

Last updated: January 2026