Installation guide
Owner’s manual
Error Codes
How to reset Maytag gas oven?
To reset a Maytag gas oven like model MGR5751BDS, press CANCEL to stop the current function; if the control is still acting up or BAKE/LOCK keeps flashing, turn power off to the range for a few minutes, then restore power and set the clock again using the steps in the MGR5751BDS owner's manual.
- Press CANCEL once to clear an active bake, broil, timer, or clean cycle.
- If the controls are locked, press and hold CANCEL and Cook & Hold for 3 seconds to unlock.
- If BAKE or LOCK flashes rapidly, press CANCEL.
- If flashing continues, switch the range OFF at the breaker (or unplug) for 2 to 5 minutes, then restore power.
- If the oven is in Sabbath Mode, press and hold Clock for 5 seconds to cancel.
- Set the time of day (the colon may flash until time is set).
- Test Bake at a normal temperature and confirm the burner lights.
- If the oven will not heat after a reset, follow the checks in oven wont heat troubleshooting gas range problems video.
| What you see | What it usually means | What to do |
|---|---|---|
| Controls do not respond | Control lock is on | Hold CANCEL + Cook & Hold 3 seconds |
| BAKE or LOCK flashing | Control detected a fault | Press CANCEL, then power-cycle 2 to 5 minutes |
| Sabbath Mode active | Special mode disables some functions | Hold Clock 5 seconds |
A proper reset clears stuck keypad inputs and temporary control faults, and it is the fastest way to recover normal baking and broiling without replacing parts.
Last updated: February 2026
Why is my Maytag gas oven not heating up?
If your Maytag MGR5751BDS gas oven is not heating, the most common cause is a weak or failed oven igniter that cannot open the gas safety valve. Also check for a power outage (this range will not operate the oven during a power failure) and make sure the controls are set correctly per the MGR5751BDS owner's manual.
- Confirm the display and oven controls respond normally (no locked controls).
- Verify the kitchen has power; this range uses pilotless ignition and the oven will not run during a power failure.
- Set BAKE to a temperature and listen for ignition; a failing igniter often glows weakly or not at all.
- Make sure the oven vent area is not blocked (heat and airflow matter for proper operation).
- Cancel the cycle and retry after 1 minute to reset a minor control glitch.
On gas ranges like the MGR5751BDS, a bad igniter is the top reason the oven will not heat even though the control is calling for heat.
| Symptom | What it usually points to | What to do next |
|---|---|---|
| No heat, no ignition, igniter does not glow | Failed igniter or no power to igniter | Check power; inspect igniter wiring; replace igniter if damaged |
| Igniter glows but burner never lights | Weak igniter (not drawing enough current) | Replace igniter |
| Broil works but bake does not | Bake igniter circuit issue | Replace bake igniter |
If you need the replacement, use the model-matched range oven burner igniter 74007498.
- Do not try to light the oven with a match; pilotless ignition shuts gas off and the oven will not operate during a power failure.
- Keep the oven vent clear; the area near the vent can get hot during use.
When the igniter is weak, the oven can fail to light or heat very slowly, which leads to undercooked food and inconsistent baking temperatures. Restoring proper ignition gets you reliable preheat and stable oven performance.
Last updated: February 2026
Why is my Maytag oven broiler not working?
If the broiler on your Maytag MGR5751BDS gas freestanding range is not working, the most common causes are a failed igniter, a problem in the control (clock/control board), or a condition that prevents safe ignition (such as a power outage). Start with basic checks, then test the ignition and control components.
- Confirm the range has power; this model uses pilotless ignition and the oven will not operate during a power failure.
- Make sure the oven door is fully closed; broiling is designed to run with the door closed.
- Set BROIL and allow a short preheat (about 2 to 3 minutes) before judging performance.
- Verify the rack position; food too close to the flame can seem like “bad broil” because it smokes or burns.
- If you recently cleaned, confirm nothing is blocking airflow; never block the oven vent.
On gas ranges like the MGR5751BDS, the broil burner needs a working ignition system and correct gas flow. These are the most common failure points:
| Symptom | Most likely cause | What to do next |
|---|---|---|
| No glow, no heat | Broil/bake igniter not heating | Inspect and replace the igniter if it will not glow/heat properly; see range oven burner igniter 74007498. |
| Igniter glows but no flame | Weak igniter or gas valve issue | Replace the igniter first (most common); if still no flame, have the gas valve/regulator checked. |
| Broil works sometimes | Control or wiring connection issue | Check harness connections; if intermittent, the control may be failing. |
- Range oven burner igniter 74007498 (most common fix when there is no ignition)
- Spark/ignition components (if surface burners also have ignition issues)
- Oven control/clock assembly (if the broil command is not being sent)
A broiler that will not ignite is usually an ignition or control problem, not a “low temperature” issue. Fixing the root cause restores safe burner operation and prevents unburned gas situations.
- Your range uses pilotless ignition; the oven will not operate during a power failure.
- Broiling guidance includes preheating briefly and broiling with the door closed.
For operating steps and broiling guidance, use the MGR5751BDS owner’s manual.
Last updated: February 2026
