Kenmore Elite 11095087401 gas dryer Parts

Common problems we see with the Kenmore Elite gas dryer model 11095087401 are long dry times or no heat (usually airflow restriction or a burner-ignition issue), the drum not turning (wear parts in the drive system), and loud thumping or squealing (worn rollers or idler parts). Routine lint and vent cleaning prevents many of these failures.

• Long dry times: clean lint screen, confirm strong airflow at the outside vent hood, check for crushed or kinked venting
• No heat: verify gas supply is on, then check ignition components such as the igniter 279311 and dryer radiant sensor WP338906
• Won’t start: confirm power at the outlet and that the door fully latches
• Drum won’t tumble: inspect belt path and idler system; the dryer idler pulley 279640 is a common wear item
• Loud rumbling/thumping: worn drum support rollers such as the support WPW10314173
• Overheating or shutting down: restricted venting or lint buildup inside the cabinet

Your manual calls out that a blocked lint screen increases drying time and that the dryer should not be operated with the lint screen loose, damaged, blocked, or missing. It also warns against improper venting and recommends heavy metal venting (rigid metal preferred). See the owner's manual.

On a gas dryer like the Kenmore Elite 11095087401, restricted airflow can cause poor drying, overheating, and repeated cycling issues. Keeping the lint screen and exhaust path clear protects the burner system, motor, and fabrics.

Last updated: February 2026

For Kenmore Elite gas dryer model 11095087401, a hard reset is simple: unplug the dryer (or switch the breaker off) for about 1 to 5 minutes, restore power, then reselect your cycle and press and hold START to run. Use the owner's manual for the exact control steps and lock settings.

• Press PAUSE/CANCEL twice to stop the cycle and clear settings.
• Unplug the dryer for 1 to 5 minutes (or turn the breaker off).
• Plug back in (or turn the breaker on).
• Select a cycle again.
• Press and hold START for about 3 seconds to begin.

These model-specific control behaviors commonly look like a reset problem:

• Control Locked is on: press and hold AUTO DRY LEVEL for 3 seconds to unlock.
• The dryer shut off after sitting: if you do not press START within 5 minutes of choosing a cycle, the dryer can shut off and you must reselect settings.
• The cycle was interrupted too long: if the door is open or the cycle is paused for more than 5 minutes, reselect the cycle before restarting.

Before replacing parts, confirm these basics:

• Door closes and latches securely.
• Power is on and the dryer is plugged into a grounded 3-prong outlet.
• Venting is not crushed or kinked (restricted airflow can cause overheating symptoms).
• Lint screen is clean.

A hard reset clears temporary electronic “hang-ups,” but repeated lockups usually point to a control setting (like Control Locked), a power interruption, airflow restriction, or a heating/ignition issue that needs troubleshooting.

Last updated: February 2026

On the Kenmore Elite dryer model 11095087401, the model and serial number label is located at the top inside the dryer door well. Open the door and look along the upper inside edge of the door opening to find the sticker/plate.

• Open the dryer door fully and turn on a bright light.
• Look at the top inside lip of the door opening (the door well).
• Check for a model/serial label with a barcode and printed numbers.
• Wipe lint or residue off the area so the text is readable.
• Write down the full model number and serial number before ordering parts.

We use the exact model number to match the correct Kenmore Elite gas dryer parts (like the drum support roller, idler pulley, igniter, or gas valve components) so you do not end up with a similar-looking part that does not fit.

If the label is worn or hard to read, the model number is also recorded in the owner's manual product record section, which is handy if you wrote it down when the dryer was new.

Last updated: February 2026

To find the cubic feet (drum capacity) of your Kenmore Elite gas dryer model 11095087401, we calculate the drum’s internal volume from its measurements. Use the measurement method in your owner's manual for access and safety steps, then measure the drum and apply the formula below.

1. Unplug the dryer and let it cool completely.
2. Open the door and measure the inside drum diameter (left to right through the center).
3. Measure the inside drum depth (front lip to the back wall of the drum).
4. Convert inches to feet and calculate volume.

• Drum diameter (inches)
• Drum depth (inches)
• Measure inside the drum, not the cabinet
• Round to the nearest 1/8 inch for best accuracy

Most dryer drums are shaped like a cylinder.

• Radius (ft) = (Diameter in inches ÷ 2) ÷ 12
• Depth (ft) = (Depth in inches) ÷ 12
• Cubic feet = π × (Radius²) × Depth

Using the example:

• Radius = 2.25 ÷ 2 = 1.125 ft
• Volume = 3.1416 × (1.125²) × 1.83 ≈ 7.3 cu ft

Drum capacity helps us match the dryer to your laundry loads and compare models. It also helps when diagnosing performance complaints (overloading can increase dry time and strain drum support parts).

If the dryer is noisy or not tumbling smoothly, these common wear parts can be involved:

• Support WPW10314173 (drum support roller)
• Dryer idler pulley 279640 (belt tension)
• Dryer repair kit 4392067 (common wear items bundled)

Last updated: February 2026

A Kenmore dryer typically lasts 10 to 13 years. Your Kenmore Elite gas dryer 11095087401 can often reach or exceed that range when airflow is kept clear (lint screen and venting) and normal wear parts are replaced as needed; see the maintenance schedule in the owner's manual.

• Loads per week: more cycles equals more wear on the drum support, belt path, and motor.
• Airflow restrictions: clogged lint screen or venting increases heat and run time.
• Heat system condition (gas models): weak ignition components can cause repeated cycling.
• Preventive cleaning: the manual recommends removing accumulated lint from the cabinet and exhaust vent about every 2 years (more often with heavy use).
• Timely wear-part replacement: rollers, idler pulley, and blower wheel wear gradually and can be serviced before they damage other components.

If your dryer is otherwise in good shape, replacing a few high-wear parts often restores quiet operation and normal drying:

• Dryer repair kit 4392067 (common wear items bundled for a refresh)
• Support WPW10314173 (drum support roller)
• Dryer idler pulley 279640 (belt tension)
• Dryer blower wheel WP697772 (air movement)
• Dryer thermistor WP8577274 (temperature sensing)

Most “old dryer” complaints are really airflow, lint buildup, or wear-part issues. Keeping the venting clear and servicing rollers and the idler pulley helps your 11095087401 dry faster, run cooler, and avoid bigger repairs.

Last updated: February 2026