Craftsman 358355141 chainsaw Parts

The most common problems we see on the Craftsman 358355141 gas chainsaw are hard starting or stalling, fuel leaks, rough running, and cutting issues caused by a dull or loose chain. Most of these trace back to the fuel system, carburetor diaphragms, or bar and chain setup; use the owner's manual for model-specific checks and adjustments.

• Won’t start or only starts on choke: stale fuel, cracked fuel line, carburetor diaphragm problems
• Starts then dies at idle: air leak at fuel lines or crank seals, carburetor metering issue
• Leaking gas: split fuel line, loose fitting, damaged fuel cap seal
• Runs rough or surges: carburetor diaphragm wear, clogged fuel pickup, air leak
• Cuts crooked or slowly: dull chain, incorrect chain tension, worn bar rails

1. Drain old fuel and refill with fresh, properly mixed 2-cycle fuel.
2. Inspect the fuel line for cracks or softness; replace with the fuel line 530069216 if it’s damaged.
3. Check the fuel cap for a good seal; replace the fuel cap 530014347 if it’s cracked or leaking.
4. Confirm chain tension and sharpness; a stretched or damaged loop should be replaced (for example, chain 91PX052G if that is the chain spec you’re using).
5. If it still runs poorly, plan on servicing the carburetor diaphragms (common wear item).

Fuel leaks and lean running can damage the engine, and a dull or improperly tensioned chain increases kickback risk and makes the saw work harder. Keeping the fuel system tight and the bar and chain maintained prevents most repeat failures.

Last updated: March 2026

The model number for this Craftsman gas chainsaw is 358355141. You’ll find it on the saw’s model tag, and it should match the number used to look up parts diagrams, the correct bar and chain, and the right fuel system parts in the Craftsman 358355141 owner's manual.

Look for a model tag or label on the chainsaw body. Common locations include:

• The starter housing (recoil cover) area
• The rear handle or handle frame
• Near the oil and fuel tank area
• On the crankcase side of the engine housing

Craftsman chainsaws often look similar across model families, but parts can differ by model number. Using 358355141 helps ensure you get the correct fit for items like:

• Fuel line routing and tank fittings
• Recoil starter components
• Guide bar and chain length compatibility
• Carburetor diaphragm and gasket sets

If you’re confirming you have the right cutting setup, match the model number first, then verify bar and chain specs in the manual.

• A 14-inch bar option is listed for this model (example: bar 140SDEA041)
• A 16-inch bar option is also listed (example: bar 160SDEA041)
• Chain must match the bar’s pitch, gauge, and drive link count

The correct model number prevents ordering the wrong Craftsman chainsaw parts, reduces downtime, and helps avoid issues like fuel leaks, hard starting, or poor cutting performance caused by mismatched components.

Last updated: January 2026

On a Craftsman chainsaw like model 358355141, the model number is printed on a rating label attached to the saw body. We most often see it on the side of the engine housing, near the rear handle, or on the underside of the unit; match it to the number shown in the 358355141 owner's manual.

Look for a sticker or metal tag on the saw housing (not on the bar or chain).

• Side of the engine/motor casing (starter side or clutch side)
• Rear handle area (near the trigger or handle mount)
• Bottom of the saw body (underside of the crankcase area)
• Near the fuel tank or oil tank area
• Under the top cover (near the air filter cover on some versions)

The model label is usually a small rectangle with printed numbers and letters.

• Write the model number exactly as printed (all digits, no spaces added)
• Take a clear photo before the label wears further
• Clean the area gently with a dry rag if it is oily or dusty
• Avoid scraping the label; it can remove the ink

The model number ensures we match the correct parts and diagrams for your chainsaw, especially for fit-sensitive items like a fuel line, bar, chain, or carburetor gaskets.

Last updated: January 2026