Owner’s manual
What old chainsaws are worth money?
Older chainsaws are worth the most money when they are collectible (rare model, early production, unusual features) and in excellent condition, especially if they are complete and run. For a Craftsman 358351040, value is usually strongest as a usable vintage saw or a parts donor, not a high-dollar collector piece; confirm original specs in the Craftsman 358351040 operator's manual.
What makes an old chainsaw valuable
- Rarity and demand: limited production, early versions, or models with a strong collector following
- Condition: clean cases, intact decals, no cracks, minimal corrosion
- Completeness: correct bar/chain, covers, chain brake parts, and hardware present
- Running status: starts, idles, accelerates, and oils the bar properly
- Original configuration: fewer non-original modifications typically brings higher interest
- Documentation and extras: original case, tools, and paperwork can add value
Quick value tiers (typical market behavior)
| Tier | What it looks like | Typical buyer | Typical outcome |
|---|---|---|---|
| Parts-only | Missing parts, seized engine, heavy wear | Repair hobbyists | Lower value; priced for parts |
| Usable vintage | Starts and cuts; normal wear | Homeowners, landowners | Moderate value; practical purchase |
| Collectible | Rare model, very clean, complete, often stored well | Collectors | Higher value; premium pricing |
| NOS | New old stock, unused, boxed | Collectors | Highest value in most cases |
How to evaluate your saw before you sell it
- Check the engine compression (a strong pull with resistance is a good sign)
- Verify fuel system integrity (no cracked lines, no leaking tank or cap)
- Confirm oiler function (bar oil delivery while running)
- Inspect bar and chain for excessive wear; a worn setup reduces value
- Look for safety features working (chain brake, throttle lockout)
If you’re restoring a non-running unit to improve resale, fuel delivery issues are common on older gas saws; replacing fuel lines with a correct kit such as the line kit 530069216 is a typical first step.
Why it matters
Knowing whether a saw is “collectible” or simply “useful” helps you price it correctly and decide whether repairs (fuel lines, carburetor service, ignition tune-up) are worth doing before listing it.
Last updated: February 2026
What model is my Craftsman chainsaw?
Your Craftsman chainsaw’s model number is printed on a label on the saw itself. For this unit, the manual lists the model as 358.351040 (often shown without the dot as 358351040); the model and serial number are found on the product label. See the 358351040 owner's manual for the exact label wording and where it’s referenced.
Where to find the model number label
Check these common spots on a Craftsman gas chainsaw like model 358351040:
- On the rear handle area near the trigger
- On the starter housing (recoil cover) side
- Near the fuel tank or oil tank area
- On the bottom of the saw body near the bar mount
- Near the muffler side cover (look for a stamped or printed tag)
What to write down (and why)
Record both the model number and the serial number so you can match parts like a carburetor, fuel line, or bar and chain correctly.
- Model number (example: 358.351040 or 358351040)
- Serial number (unique to your saw)
- Date of purchase (helpful for service history)
Quick ID checklist
Use this table to avoid ordering the wrong Craftsman chainsaw parts.
| Item to match | What it looks like | Why it matters |
|---|---|---|
| Model number | Usually starts with 358 on older Craftsman saws | Determines the correct parts diagrams and part fit |
| Serial number | Longer number or mixed characters | Helps identify production run differences |
| Bar length marking | Often listed in the manual (example: 14-inch) | Helps match the correct bar and chain size |
Why it matters
Craftsman chainsaws can look similar across multiple model families, but small differences affect fit for ignition parts, fuel system parts, and cutting components. Using the exact model number from the label keeps repairs accurate and reduces returns.
Last updated: February 2026
Who makes Craftsman chainsaws now?
Craftsman chainsaws are built by different manufacturers depending on the model and production era. For the Craftsman 358351040 gas chainsaw, the design and parts family commonly align with AYP-era equipment; newer Craftsman chainsaws are often produced under Stanley Black & Decker’s Craftsman brand through contracted manufacturing.
How to tell who made your specific Craftsman chainsaw
The most reliable way is to match the model number and parts breakdown for your saw.
- Use the exact model number on the data plate: 358351040
- Compare the illustrated parts list and service info in the 358351040 owner’s manual
- Check whether common service parts match AYP-style part numbering (many do on this model)
- Use the bar and chain specs listed for the saw (this model is a 14-inch class saw per the manual)
- When ordering parts, match by part ID and description, not by “who made it”
What “made by” means for Craftsman
Craftsman is a brand; manufacturing can change over time even when the Craftsman name stays the same.
| What you have | What it usually indicates | What to do next |
|---|---|---|
| Older Craftsman gas saws (like 358.xxxxxxx models) | Commonly tied to AYP/Poulan-family designs | Use model-based parts matching |
| Newer Craftsman gas saws | Often produced under Stanley Black & Decker’s brand ecosystem via suppliers | Use the exact model number and serial |
Why it matters when buying parts
Parts fit is driven by the model number and revision, not the logo on the cover. For example, fuel system parts are model-specific; if you are troubleshooting fuel delivery or leaks, matching the correct fuel line routing and grommets matters.
If you are servicing the fuel system on this model, the line kit 530069216 is a common starting point when fuel lines are brittle, leaking, or incorrectly routed.
Last updated: February 2026
Will an Oregon chain fit a Craftsman chainsaw?
Yes, an Oregon chain can fit a Craftsman chainsaw, but it must match the exact bar length, pitch, gauge, and drive link count used on your Craftsman model 358351040. We recommend confirming those specs in the 358351040 owner's manual before ordering.
How to confirm chain fitment (what must match)
Check these four items on your current chain or guide bar markings:
- Bar length (this model is commonly a 14-inch saw; confirm your actual bar)
- Pitch (example: 3/8 low profile vs standard 3/8)
- Gauge (example: .050 inch)
- Drive link count (must match your bar)
If all four match, an Oregon replacement chain will fit and run correctly.
Quick compatibility checklist
Use this table to avoid the most common ordering mistakes:
| Spec to match | Where to find it | What happens if it’s wrong |
|---|---|---|
| Bar length | Stamped on bar or measured | Chain may be too short or too long |
| Pitch | Stamped on bar or chain package | Won’t mesh with sprocket/bar correctly |
| Gauge | Stamped on bar | Chain won’t sit in the bar groove |
| Drive links | Count links or read chain stamp | Tensioner cannot set correctly |
If you are switching bar and chain together
If your bar is worn (rails spread, groove shallow, nose sprocket rough), replacing the bar and chain as a set is often the cleanest way to ensure compatibility. For this model, we list bar options such as the bar 140SDEA041 and bar 160SDEA041; match the bar length and then choose an Oregon chain that matches that bar’s pitch, gauge, and drive links.
Why it matters
A mismatched chain can derail, cut poorly, and increase kickback risk. Keeping the correct chain specs also helps the oiler lubricate properly and reduces wear on the clutch drum and sprocket.
Last updated: February 2026
Is 40 1 or 50 1 better for chainsaws?
For the Craftsman chainsaw model 358351040, 40:1 is the correct and better mix because it matches the factory fuel specification (3.2 oz of 2-cycle air-cooled oil per 1 gallon of gasoline). Use 50:1 only if a specific chainsaw manual calls for it. See the 358351040 operator's manual for the exact mix and fueling steps.
What to use for this Craftsman 358351040
- Mix 40:1 fuel (gasoline + 2-cycle air-cooled engine oil).
- Measure oil accurately; too little oil increases wear, too much oil can smoke and foul the spark plug.
- Use fresh, regular unleaded gasoline.
- Use 2-cycle oil labeled for air-cooled engines.
- Do not use automotive oil or marine 2-cycle oil.
Quick mix chart
| Mix ratio | Oil per 1 gallon gas | Oil percentage | When it fits |
|---|---|---|---|
| 40:1 | 3.2 oz | 2.5% | Craftsman 358351040 spec; best choice |
| 50:1 | 2.6 oz | 2.0% | Only for saws that explicitly specify 50:1 |
Why 40:1 vs 50:1 matters
The fuel mix is the engine’s lubrication. Running lean on oil (such as using 50:1 in a saw designed for 40:1) reduces lubrication to the piston, rings, and crank bearings, which can shorten engine life and cause scoring.
Tips to avoid common fuel-mix problems
- Mix fuel in an approved gas can, not in the chainsaw tank.
- Shake the container before each refill to re-blend oil and gas.
- If the saw runs rough or won’t start after fueling, check for stale fuel and consider carburetor service; the tips for a hard to start chainsaw guide helps narrow it down.
- If you suspect cracked or leaking fuel lines, replace them; the line kit 530069216 is a common fix for fuel delivery issues.
Last updated: February 2026
What is the Craftsman 358351040 42 cc 2 cycle gas 18 chainsaw?
The Craftsman 358351040 is a 2-cycle gasoline chainsaw covered by an operator’s manual that identifies it as a 2.1 cu. in./34cc saw (often paired with a 14-inch setup). For exact bar/chain configuration and operating specs, use the 358351040 operator's manual.
What this model is (and what it is not)
The model number 358351040 is the most reliable way to identify your saw because Craftsman produced similar-looking chainsaws in different engine sizes and bar lengths.
- Model identification: 358351040 (shown on the unit decal)
- Engine type: 2-cycle gasoline
- Manual-listed displacement: 2.1 cu. in. (34cc)
- Manual-listed bar length: 14-inch
- Common confusion: listings that describe 42cc and 18-inch may refer to a different Craftsman model family, not 358351040
Key operating basics you should follow
The operator’s manual for Craftsman 358351040 calls out a 40:1 fuel mix using air-cooled 2-cycle oil.
- Mix fuel in an approved container (not in the tank)
- Use regular unleaded gasoline with 40:1 air-cooled 2-cycle oil
- For 1 gallon of gas, mix in 3.2 oz of 2-cycle oil
- Avoid automotive oil and marine/boat oils
- For storage beyond 30 days, use stabilizer and run the engine several minutes to circulate it
Quick spec comparison (common mix-up)
| Item | Craftsman 358351040 (per manual) | “42cc / 18-inch” description |
|---|---|---|
| Displacement | 34cc (2.1 cu. in.) | 42cc |
| Bar length | 14-inch | 18-inch |
| Best way to confirm | Model decal + manual | Product listing text |
Why it matters
Correct identification affects everything from bar and chain fit to carburetor parts, fuel line routing, and the right fuel mix. Using the wrong specs can lead to poor performance, hard starting, or premature wear.
Last updated: February 2026
