Kenmore 79036933905 gas range Parts

On the Kenmore gas range model 79036933905, you adjust the surface-burner flame by setting the burner to its lowest position, then fine-tuning the valve screw inside the knob stem so the flame stays lit and stays as small as possible without going out (especially when turning from LITE to LOW).

Adjusting the low flame (simmer) setting

Before you start, make sure the burner cap and burner head are seated correctly and the burner lights normally.

• Push in and turn the knob to LITE until the burner ignites.
• Quickly turn the knob to the LOWEST setting.
• If the flame goes out, turn the knob OFF.
• Pull the control knob straight off the valve stem.
• Insert a thin-blade screwdriver into the hollow valve stem to engage the slotted adjustment screw.
• Turn the screw slightly to increase or decrease the flame.
• Reinstall the knob and test again; the goal is a stable, very small flame that does not extinguish.

For the exact procedure and illustration, follow the steps in the installation guide.

What the flame should look like (quick checks)

A correct flame is steady and sized to the pan.

What you see	What it usually means	What to do
Flame goes out on LOW	Low setting too low	Open the low-flame screw slightly
Very large flame on LOW	Low setting too high	Close the low-flame screw slightly
Flame extends past pan edge	Flame set too high for cookware	Turn down; use proper pan size
Clicking continues	Knob left in LITE	Turn knob out of LITE after ignition

Why it matters

A properly adjusted low flame improves simmer control, helps prevent nuisance flame-outs, and supports safer, more efficient cooking (flame should not extend beyond the utensil edge). For normal operation details, we follow the guidance in the 79036933905 owner’s manual.

Last updated: February 2026

A Kenmore gas range like model 79036933905 typically lasts 15 years with normal household use. Keeping burners clean, ensuring good kitchen ventilation, and addressing ignition or temperature issues early helps you get the full service life from the range.

Typical lifespan and what affects it

A gas range’s life depends most on heat exposure, cleaning habits, and how hard key components work (igniters, gas valve, controls).

• Daily heavy cooking shortens life; light use extends it
• Frequent self-clean cycles add heat stress to wiring and controls
• Spills and boilovers can clog burner ports and damage igniters
• Poor ventilation increases grease buildup and heat around the control area
• Promptly fixing weak ignition prevents strain on the gas valve and igniter

Maintenance that helps you reach 15 years

Use the care and cleaning steps in the 79036933905 owner’s manual and keep these habits consistent:

• Wipe up heavy spillovers before running self-clean
• Use an exhaust hood or open a window during self-clean for ventilation
• Keep surface burner caps seated correctly after cleaning
• Avoid soaking or flooding igniter areas with water or cleaner
• Replace worn consumables (like the oven light bulb) before they fail completely

Parts that commonly determine “end of life”

Many ranges get replaced because a few high-wear parts fail at once. These are common decision points:

Symptom	Common cause	Example part for this model
Oven won’t heat or takes too long to light	Weak igniter	Frigidaire range oven burner igniter 5303935066
Oven temperature swings or bakes unevenly	Sensor drifting out of range	Range oven temperature sensor 5304504897
Oven light out	Burned-out bulb	Appliance light bulb, 40-watt 316538904

Why it matters

A 15-year lifespan is realistic when ignition and temperature control stay reliable. Small issues like a slow-glowing igniter can create longer preheat times and inconsistent baking, which often feels like the range is “wearing out” even when it is repairable.

Last updated: February 2026

On the Kenmore gas range model 79036933905, the model and serial number are printed on the serial plate, typically on the oven front frame behind the oven door or on the drawer side frame. Use the exact model number when ordering parts or scheduling service; see the 79036933905 installation guide.

Where to look on the range

Check these common label locations first:

• Open the oven door and look along the oven front frame (behind the door)
• Pull out the storage or broiler drawer and check the drawer side frame
• Look for a metal or foil serial plate (not a paper sticker)
• Wipe grease and dust off the frame so the print is readable
• Write down the full model number and the full serial number

What the serial plate tells you (and why it matters)

The serial plate is more than an ID tag; it helps match the correct Kenmore parts and setup information.

• Confirms the exact model for part compatibility
• Lists burner ratings (BTU) for the appliance
• Identifies fuel type and the gas pressure setting from the factory

Quick comparison: oven door frame vs drawer frame

Location	What to do	When it is most likely
Oven front frame (behind oven door)	Open door, inspect the front frame edges	Many models place the plate here
Drawer side frame	Pull drawer out, inspect side rails/frame	Some models place the plate here

Tips for ordering the right parts

When you contact us or shop for replacement parts, use the full model number and serial number from the plate.

Common examples for this model include ignition and temperature-related parts such as the frigidaire range oven burner igniter 5303935066 or the range oven temperature sensor 5304504897.

Last updated: February 2026

On the Kenmore 79036933905 gas range, replacing a surface-burner spark electrode (igniter) means shutting off power and gas, lifting the cooktop as needed, removing the electrode from the burner base area, transferring the wire connection, then reassembling and verifying the burner lights within a few seconds. See the 79036933905 installation guide for burner base and electrode placement details.

Safety first

• Turn off electrical power to the range at the breaker (igniters spark on household power).
• Close the main gas shutoff valve.
• Let all burner parts cool completely.
• Work in a well-ventilated area and keep flames and sparks away.
• If you smell gas at any point, stop and keep the gas shutoff closed.

Replacement steps (surface burner spark electrode)

1. Remove the burner grate, then lift off the burner cap and burner base as applicable.
2. Locate the electrode at the burner base near the gas opening (it sits next to the burner head area).
3. Remove the mounting screw holding the electrode.
4. Disconnect the electrode wire connector.
5. Connect the wire to the new electrode; make sure the connector is fully seated and secure.
6. Reinstall the electrode and tighten the mounting screw.
7. Reinstall burner base and cap; confirm the burner is aligned and level.
8. Restore power and open the gas shutoff; test ignition.

What “normal” looks like after replacement

Check	Normal result	If not normal
Spark sound	Rapid clicking at LITE	Check wire connection and electrode position
Time to light	Lights within ~4 seconds	Purge air from line, recheck cap alignment
Knob position	Turn out of LITE after lighting	If left on LITE, igniter keeps sparking

Why it matters

A properly positioned electrode and correctly seated burner cap help the burner ignite quickly and prevent nuisance clicking, delayed ignition, and uneven flames.

Parts that are commonly involved

If the electrode is damaged or the burner still will not light reliably, these model-compatible parts are often checked next:

• Range surface burner igniter and orifice holder 316540700 (electrode/holder assembly)
• Cooktop module 808608802 (spark module that drives igniters)
• Range surface burner cap, 5,000-btu (matte black) 5304508441 (cap alignment affects ignition)

Last updated: February 2026