Kenmore 10657989700 side-by-side refrigerator Parts

For Kenmore model 10657989700 (side-by-side), the exact cubic-foot capacity is listed on the model’s rating label and in the 10657989700 owner's manual. If you are seeing “Kenmore Elite 30.6 cu. ft.” online, that typically refers to a different French door style, not this side-by-side model.

How to find the capacity on your refrigerator

We recommend checking these common locations first:

• Inside the fresh food compartment on a side wall near the crisper drawers
• On the ceiling or upper side wall inside the refrigerator section
• Behind the toe grille (base grille) area
• On the back exterior panel near the power cord
• In the specifications section of the 10657989700 owner's manual

Quick ID check: side-by-side vs. French door

If the listing you found shows a different door style, the capacity will not match your unit.

Feature	Side-by-side (your 10657989700)	French door (often “Elite” listings)
Door layout	Two tall doors	Two upper doors plus a bottom freezer drawer
Typical capacity range	20 to 26 cu. ft.	25 to 31 cu. ft.
Common confusion	Model family numbers look similar	Listings may omit full model number

Why it matters

Cubic-foot capacity affects how you shop for replacement parts and accessories (like shelves, bins, and filters) and helps you compare cooling performance and storage space accurately across Kenmore refrigerator models.

Last updated: February 2026

Kenmore Elite refrigerator dimensions vary by the exact model and style (side-by-side, French door, top freezer). For Kenmore model 10657989700 (a side-by-side), we use the exact measurements listed in the 10657989700 owner's manual so you can confirm fit, door swing clearance, and installation space before moving or replacing the unit.

Typical Kenmore Elite refrigerator size ranges

If you do not have the exact model number, these ranges help you estimate what will fit in your kitchen opening.

• Side-by-side: about 32 to 36 in. wide, 65 to 71 in. tall, 30 to 35 in. deep
• French door: about 33 to 36 in. wide, 68 to 71 in. tall, 29 to 36 in. deep
• Top freezer: about 28 to 33 in. wide, 61 to 67 in. tall, 28 to 34 in. deep
• Plan extra space for door swing, handles, and airflow behind the cabinet

How we recommend measuring (so it fits the first time)

Measure the space and the refrigerator, then compare.

• Measure the opening width at the front and back (cabinets are not always square)
• Measure height to the lowest overhead cabinet or soffit
• Measure depth from the back wall to the front edge of counters
• Add clearance for hinges/handles and for pulling out crisper drawers
• Leave ventilation space as specified in the 10657989700 owner's manual

Quick comparison: opening size vs. appliance size

What you measure	What it affects	What to allow for
Width	Door swing, leveling, trim fit	A little extra on both sides
Height	Hinge clearance, moving into place	Extra room above the cabinet
Depth	Counter alignment, door clearance	Handles and rear airflow space

Why it matters

Correct dimensions prevent delivery problems, doors that will not open fully, and poor cooling from restricted airflow. Getting the clearances right also helps avoid water line kinks for the dispenser and ice maker.

Last updated: February 2026

The most common problems we see on Kenmore refrigerators like model 10657989700 are cooling issues, water leaks, ice maker or dispenser failures, and unusual noises. These usually trace back to airflow restrictions, frost buildup in the defrost system, or worn water-system parts; use the 10657989700 owner's manual for model-specific checks and settings.

Common symptoms and what they usually mean

• Not cooling or warm temperatures: dirty condenser coils, evaporator fan not running, or a defrost problem causing ice buildup
• Water under the refrigerator: clogged defrost drain, loose water line, or a leaking inlet valve
• Ice maker not making ice: water supply issue, failed ice maker module, or a bad inlet valve
• Water dispenser slow or not dispensing: clogged water filter, air in the line, or low house water pressure
• Clicking, buzzing, or rattling: fan blade hitting ice, condenser fan obstruction, or compressor start components

Quick checks we recommend first (safe and fast)

1. Confirm the doors seal and close fully; poor sealing causes temperature swings and frost.
2. Set temperatures to normal targets (about 37°F fresh food and 0°F freezer).
3. Clean condenser coils and make sure airflow around the cabinet is clear.
4. If water or ice is affected, verify the refrigerator is connected to a cold water pipe and allow 24 hours after installation or heavy use for the water supply to cool.
5. Replace the water filter on schedule; a restricted filter can reduce dispenser flow and ice production.

Parts that commonly solve these problems on 10657989700

Problem area	Common fix	Example model-matched part
Water/ice supply	Replace a clogged filter	Genuine Kenmore refrigerator water filter EDR3RXD1
No water to dispenser/ice maker	Test and replace inlet valve	Refrigerator inlet valve W10408179
No ice production	Replace ice maker assembly	Refrigerator ice maker WPW10190965
Frost buildup, warm fridge	Check defrost heater/thermostat	Refrigerator heater WP2323198 and refrigerator bi-metal thermostat WPW10225581

Why it matters

Catching the root cause early protects food temperatures, prevents recurring leaks, and reduces strain on major components like the compressor and electronic control.

Helpful DIY guidance

For water and filter-related issues, follow how to replace the water filter in a Kenmore refrigerator. For model-family troubleshooting, use Kenmore 106 model refrigerator error codes to interpret any displayed codes.

Last updated: February 2026

Most Kenmore refrigerators average 10 to 15 years of service life. For a Kenmore side-by-side like model 10657989700, lifespan depends most on basic care such as cleaning, good door sealing, and keeping airflow clear; those habits reduce compressor and cooling-system strain (see the 10657989700 owner's manual).

Typical lifespan ranges (what we see most often)

• 10 to 15 years: common for many household refrigerators
• 15 to 20 years: achievable with consistent maintenance and timely repairs
• Under 10 years: more likely when coils are clogged, doors leak air, or the unit runs hot

Appliance type	Typical lifespan	What usually ends it first
Side-by-side refrigerator	10 to 15 years	Sealed system wear, control issues, airflow problems
Top freezer refrigerator	12 to 18 years	Thermostat/control wear, door seal leaks
Bottom freezer refrigerator	10 to 15 years	Fan/defrost issues, control problems

What extends the life of your Kenmore 10657989700

• Clean condenser coils regularly (dust buildup makes the compressor run longer)
• Confirm proper air circulation inside the cabinet (avoid blocking vents)
• Keep door gaskets sealing so the refrigerator does not run constantly
• Use the correct water filter and replace on schedule if you have a dispenser
• Address unusual noises early (fan rubbing, clicking, or buzzing can signal wear)

Quick maintenance checklist

Task	Good interval	Why it helps
Clean condenser coils	Every 6 to 12 months	Lowers run time and heat stress
Check door seal for gaps	Monthly	Prevents warm air and moisture intrusion
Verify temperatures	Monthly	Catches cooling decline early
Replace water filter	About every 6 months	Protects water flow and taste

Why it matters

A refrigerator that runs hotter or longer than normal wears out key components faster, especially the compressor, fans, and defrost system. The care steps above help your Kenmore side-by-side maintain stable temperatures with less strain.

Last updated: February 2026

On the Kenmore 10657989700 side-by-side refrigerator, the water filter is located in the base grille at the bottom front of the unit. You access it from the front; the filter uses a cap and an eject-style release described in the 10657989700 owner's manual.

How to find it fast

• Look at the very bottom front of the refrigerator for the base grille.
• Open both doors if you need more room to work at the grille.
• Find the filter cap area in the grille; the cap stays with the refrigerator when you change filters.
• If you are removing the filter to run unfiltered water temporarily, keep the cap and install it in the grille as directed.

What you will see at the base grille

What you see	What it means	What to do
Base grille at bottom front	Filter housing is behind/in the grille area	Access filter from the front
Filter cap	Cap transfers to the replacement filter	Save and reuse the cap
Eject-style release	Filter comes out by pressing eject and pulling	Press eject, then pull the cap/filter out

Parts that commonly apply to filter changes

If your filter is missing its cap or you are replacing the cartridge, these model-compatible parts are commonly used:

• Genuine Kenmore refrigerator water filter EDR3RXD1 (replacement filter cartridge)
• Refrigerator water filter cap (black) WP2260518B (cap that fits the filter opening)

Why it matters

Knowing the filter is in the base grille helps you avoid removing interior shelves or panels unnecessarily. It also makes routine maintenance easier, which helps water flow and reduces issues like slow dispensing after a clogged or incorrectly installed filter.

Last updated: February 2026

On Kenmore side-by-side refrigerator model 10657989700, the model number is printed on the appliance identification label; we typically find this label inside the fresh food (refrigerator) compartment on a side wall or near the ceiling, and it lists both the model and serial information. See the 10657989700 owner's manual for the exact label location and diagrams.

Common places to check first

• Inside the refrigerator section on the left or right interior wall
• On the ceiling area inside the refrigerator compartment
• Behind the base grille area (lower front) on some Kenmore 106 models
• On the door frame (hinge side) when you open the refrigerator door
• On the back exterior panel near the power cord (less common)

What the label looks like and what to write down

The ID label usually includes a model number and a serial number. Record both before ordering parts like a water filter or ice maker.

Item on label	Why we need it	Example format
Model number	Ensures parts fit your exact refrigerator	10657989700
Serial number	Helps match production series and revisions	Letters plus numbers

Why it matters

Kenmore side-by-side refrigerators can look similar across multiple 106-series models, but parts such as the water filter cap, inlet valve, or ice maker can vary by revision. Using the exact model number helps us match the correct Kenmore refrigerator parts the first time.

Last updated: February 2026

Kenmore model 10657989700 was made for Sears by Whirlpool. The 106 prefix in the model number is the key identifier that ties this Kenmore side-by-side refrigerator to Whirlpool manufacturing.

How to confirm it on your refrigerator

We recommend verifying the full model number from the rating label, then matching the prefix.

• Look for the model and serial tag inside the fresh food compartment (often on a side wall)
• Confirm the model reads 10657989700 (all digits, no missing characters)
• Use the first three digits (106) as the manufacturer prefix
• Keep the full model number handy when ordering parts like a water filter or inlet valve

Kenmore manufacturer prefix quick guide

Model prefix	Manufacturer (made for Sears)	What it means for parts
106	Whirlpool	Many components cross to Whirlpool-style parts
103	Roper	Different parts families than 106 models
628	Kelvinator	Different designs and part numbering

Why it matters

Knowing Whirlpool made Kenmore 10657989700 helps us narrow down the correct part design and troubleshooting approach, especially for common systems like the ice maker, water dispenser, and defrost circuit.

Helpful next step

For model-specific diagrams, part locations, and maintenance details, use the 10657989700 owner's manual.

Last updated: February 2026