Kenmore 66574363K2 dishwasher Parts

To hard reset your Kenmore dishwasher model 66574363K2, we recommend clearing the current cycle by using CANCEL/DRAIN, letting the unit drain, then restarting a fresh cycle with START/RESUME. This resets the cycle logic and clears most “stuck” conditions. See the 66574363K2 owner's manual for the exact button sequence on your control panel.

Reset steps (works for most “won’t respond” situations)

• Close the door fully (the dishwasher must be closed to drain).
• Press CANCEL/DRAIN once.
• Wait about 2 minutes for the drain to complete.
• Select your desired cycle and any options.
• Press START/RESUME to begin.
• If the controls are locked, press and hold HEATED DRY for 4 seconds to toggle Lock On off.

If you are trying to “reset” because the dishwasher is locked

The control lock can look like a failure because most buttons will not work.

Symptom	What it usually means	What to do
LOCK ON light is lit	Controls are disabled	Hold HEATED DRY for 4 seconds
Buttons beep or light flashes	Lock is still enabled	Turn Lock Off, then press START/RESUME
Door opens but cycle will not resume	Lock is on	Turn Lock Off, then press START/RESUME

Why it matters

Using CANCEL/DRAIN first prevents starting a new wash with leftover water in the tub, and it clears cycle indicators so the electronic control can accept a new cycle selection cleanly.

When a reset is not enough

If the dishwasher still will not start after the steps above, focus on common causes like a door not latching or a fill problem:

• Confirm the door latches firmly; a worn latch can stop operation.
• Check household water supply to the dishwasher.
• If it fills slowly or not at all, the dishwasher water inlet valve W10844024 is a common part involved.
• If you see an error code, use the Kenmore 665 model dishwasher error codes reference to match the code to the next repair step.

Last updated: January 2026

Common problems on the Kenmore 66574363K2 dishwasher include the unit not starting or stopping mid-cycle, poor cleaning from spray issues, and leaks around the door. Many of these come down to the door latch, water fill, drainage, or a blocked float/vent area; our troubleshooting steps below help narrow it fast.

Most common symptoms (and what they usually point to)

• Won’t start / stops during a cycle: door not fully latched, power interruption, or an overload reset
• Poor wash performance: spray arm blockage, low water fill, or wash system restriction
• Leaks at the front: worn door seal or door not closing squarely
• Burning smell: heater or wiring issue, or debris contacting a hot component
• Steam at the door vent during drying: normal operation (hot vapor exits the vent)

Quick checks we recommend first (5 to 10 minutes)

• Confirm the door closes tightly and latches; a loose latch can stop the cycle.
• Check the home breaker or fuse; a power interruption can cause a flashing Start/Resume light.
• Verify the water shut-off valve is fully open.
• Lift and release the overfill protection float; it must move freely and be in place.
• Look for items under the float that could jam it.

Common parts involved

Symptom	Likely area	Example part for this model
Door won’t latch or cycle stops	Door latch/strike alignment	Dishwasher door latch WP3380854
Water not filling well	Water inlet valve	Dishwasher water inlet valve W10844024
Leaking at the door	Door seal	Dishwasher door seal WPW10509257

Why it matters

A dishwasher that is not latching, not filling correctly, or overfilling can stop mid-cycle, wash poorly, or leak. Catching the root cause early helps protect the motor, pump, and kitchen flooring.

Where to confirm model-specific steps

Use the 66574363K2 owner's manual for cycle behavior, indicator light meanings, and the built-in troubleshooting checks (including door latch and float guidance).

Last updated: January 2026

On Kenmore dishwasher model 66574363K2, the F2E2 error code points to a keypad or user interface problem, where the control is not reading the button presses correctly (often a stuck key or a failed user interface). Use the troubleshooting steps in the 66574363K2 owner's manual to confirm the reset and diagnostic procedure.

What to try first (quick checks)

• Press Cancel/Drain and wait for the drain to finish.
• Power reset: turn the dishwasher OFF at the breaker for 1 minute, then restore power.
• Wipe the control panel dry; moisture can cause false key presses.
• Press each key once; if one feels stuck or triggers beeping, that supports a keypad issue.
• Start a normal cycle and watch whether the code returns immediately.

What usually causes F2E2

Most F2E2 situations come down to one of these:

• Stuck or shorted keypad on the console
• Failed user interface (touchpad) electronics
• Loose connection between the user interface and main control
• Moisture intrusion at the console

Symptom-to-cause guide

What you notice	Most likely cause	What to do next
Code returns right away after reset	Keypad/user interface fault	Inspect console area; plan for UI repair
Random beeping or “phantom” button presses	Moisture or shorted keypad	Dry panel, reset power, recheck
Some buttons work, others do not	Worn keypad contacts	Replace the user interface/keypad assembly

Why it matters

When the dishwasher cannot reliably read the keypad, it may not start, may stop mid-cycle, or may run the wrong options. Fixing the user interface issue restores normal cycle selection and helps prevent repeat interruptions.

When parts are involved

If the code persists after a reset and drying the console, the repair typically involves the console keypad/user interface or its wiring connections. For model-specific disassembly and access steps, follow the 66574363K2 installation guide.

Last updated: January 2026