Kenmore 66513213K901 undercounter dishwasher Parts

Common problems we see on the Kenmore 66513213K901 dishwasher include poor cleaning, water not draining, the dishwasher not starting, leaks, and long cycle times. Many of these issues trace back to loading, water temperature, detergent/rinse aid use, or a few serviceable parts.

• Not cleaning well: Confirm spray arms spin freely and dishes are loaded so water can reach all surfaces.
• Water not draining: Check for kinks in the drain hose and clogs at the sink connection or disposer inlet.
• Won’t start or stops mid-cycle: Make sure the door is fully latched; if Start/Resume is blinking, restart correctly.
• Not drying: Use rinse aid and consider Heated Dry; plastics and nonstick items often need towel drying.
• Leaks or suds: Use only automatic dishwasher detergent; hand soap causes overflow and leaks.

For model-specific operating tips (cycles, options, loading, and troubleshooting), use the 66513213K901 user manual.

If basic checks do not fix the issue, these parts are frequent culprits:

• Drain problems: Dishwasher drain pump WPW10348269 or a restricted drain path
• Filling problems: water supply issues or a failing inlet valve
• Leaks at the door: worn door seal
• Poor wash performance: circulation pump or sump-related issues

Catching the root cause early helps prevent repeat wash failures, water damage from leaks, and unnecessary part replacement. On the 66513213K901, correct loading and proper detergent and rinse aid use can solve a surprising number of “not cleaning” and “not drying” complaints.

Last updated: January 2026

For Kenmore dishwasher model 66513213K901, the most reliable “hard reset” is a full power reset: turn the breaker OFF (or unplug) for about 5 minutes, then restore power. If you’re trying to clear a stuck cycle, use the Cancel/Drain reset steps in the 66513213K901 owner’s manual.

Use the method that matches what the dishwasher is doing.

• Hard reset (power reset): breaker OFF (or unplug) 5 minutes, then power back ON.
• Control reset (clears a stuck cycle): press CANCEL/DRAIN twice, then reselect a cycle.
• Resume after door opened: press START/RESUME and close the door within 3 seconds.
• Control Lock on/off: press and hold HEATED DRY for 3 seconds.

This is the best “reset” when the dishwasher won’t advance or you need to restart a cycle.

1. Open the door slightly and wait for spraying to stop.
2. Press CANCEL/DRAIN to drain.
3. If you want a full control reset, press CANCEL/DRAIN twice.
4. Select a new cycle and options.
5. Press START/RESUME and close the door within 3 seconds.

A power reset clears temporary control glitches, but a Cancel/Drain reset is often the fastest way to recover from a paused or interrupted wash cycle without waiting.

Last updated: January 2026

To force a drain on your Kenmore dishwasher model 66513213K901, we recommend using the Cancel/Drain function: open the door slightly to pause, press CANCEL/DRAIN once, then close the door within 3 seconds so the unit runs a drain cycle (about 2 minutes). See the steps in the 66513213K901 use & care manual.

• Open the door slightly to stop the cycle; wait for spraying to stop.
• Press CANCEL/DRAIN one time.
• Close the door within 3 seconds.
• Let the dishwasher drain completely (the Cancel/Drain light typically turns off after about 2 minutes).
• If the door was opened too long and the cycle will not resume, press START/RESUME and close the door within 3 seconds.

If your 66513213K901 runs the drain sequence but water remains in the tub, the issue is usually a blockage or a drain-system problem rather than the control setting.

• Confirm the cycle is actually complete; some cycles pause and run longer than expected.
• Check the sink/disposer connection; a disposer knockout plug can block draining.
• Inspect the drain hose routing for kinks or crushing.
• Look for food or debris at the drain path inside the tub.
• If your setup uses an air gap, clean it if it is clogged.

Standing water can cause odors, poor wash performance, and can lead to leaks if the dishwasher overfills on the next cycle. Forcing a drain is a safe first step before troubleshooting the drain path.

Last updated: January 2026